The objective of this paper is to describe a method of monitoring engine pressure and pressure torque by measuring and analysing engine transient speed.
为此，描述了一种通过测量和分析发动机的瞬态转速来监测气缸内的压力和压力扭矩的方法。
The disturbance torques imparted by space environment are analyzed, which include gravity gradient torque, solar pressure torque, aerodynamic torque and magnetic torque.
对作用在卫星上的各种空间环境力矩进行了分析，包括重力梯度力矩、太阳光压力矩、气动力矩、剩磁力矩等。
A diagnostic method for diagnosing a diesel engine cylinder faults according the engine transient speed waveform and gas pressure torque waveform is presented in the thesis.
本文讨论了基于柴油发动机瞬态转速波形和气压扭矩波形对柴油机气缸内故障进行诊断的方法。
A power index model is formed which describes the relation of drum brake average torque with speed and pressure.
建立了某型号鼓式制动器平均制动力矩同速度和压力间的幂指数模型。
This system can complete the engine rotational speed and torque high accuracy control and the test, also engine temperature, pressure, oil consumption parameters survey.
本系统能够完成发动机的转速、转矩的高精度控制与测试，以及发动机温度、压力、油耗等指标参数的测量。
This form has the characteristics of large connection contact area, small clearance, small unit area pressure, strong anti - horizontal torque ability and strong contact stability.
这种形式具有连接接触面积大，间隙小，单位面积压力小，抗水平扭矩能力强，接点稳定性强等特点。
The roll separating force, rolling torque and contact pressure along the surface of the rolls are also evaluated by means of the finite element method.
轧制分离力、轧制力矩以及沿轧辊表面的接触压力也通过有限元法进行评估。
Torsion is the use of rotational pressure (torque) on a component. Twisting and torque and included in this category. Causes shearing, compression, and deformation of components.
扭曲是在部件上施加旋转的扭力。通常使部件被切断，压缩和变形，扭转和扭曲同属于此类别。
After analysis of measurement data, a power index model is formed which describes the relation of drum brake average torque with speed and pressure.
利用测得数据，建立了某型号鼓式制动器平均制动力矩同速度和压力间的幂指数模型。
These pages also show torque for differential pressures at full and half maximum cold working pressure for carbon steel valves.
这些内容也包括碳钢阀门在最大或一半的冷工作压力下压差的扭矩。
The sampling and dealing with of pressure, flow, power, speed, torque and the drawing of performance curve are realized basically.
基本实现了压力、流量、功率、转速、扭矩的自动采集与处理，性能曲线的绘制。
Metrical experimental studies on screw torque, axial thrust, barrel inwall pressure of twin screw pulping extruder (TSPE) were done.
对双螺杆磨浆机的螺杆扭矩、轴向推力和机筒压力进行了测量实验研究。
The loading unit realized the recycle of power as well as the perfect loading for constant torque by means of setting up pressure in advance.
加载单元，不仅能实现功率回收，还可通过预建压的方法，实现理想的恒扭矩加载。
Seat tightness achieved with torque as opposed to line pressure.
利用扭矩而不是管路压力来实现阀座的密封。
While the load pressure fluctuation, the load torque fluctuation and the rotational speed fluctuation mainly affect the steady performance of the system.
负载压力波动、加载转矩和转速的波动，主要影响系统的稳态性能。
Within the designed range, the temperature and material moisture influences on the torque, the 4th zone pressure, the 5th zone pressure, the expansion rate, and the product moisture are significant.
结果表明，在试验设计的加工温度和物料含水量范围内，加工温度和物料含水量对螺杆扭矩、第4区压力、第5区压力、产品膨化率和含水量都有极显著影响。
Strong plus pressure, strong elevation force, large output torque and strong drilling capacity can satisfy the demand for deep hole drilling.
加压力大、提拔力大、输出扭矩大，钻探能力强，能满足深孔钻探的需要。
The PLC is used in automatic pressure surge control, oil temperature control, product test control, and automatic measurement of pressure, flow, temperature, speed, torque, etc.
PLC下位机完成转向泵的压力冲击自动控制、油温自动控制、出厂试验自动控制和压力、流量、温度、转速、转矩等参数的自动测试。
It can measure drilling engineering parameter, such as drilling pressure, torque, side pressure and annular pressure etc.
钻压、扭矩、侧向力、环空压力等钻井工程参数可以随钻进行测试。
Simulation results reveal that equivalent rotational inertia, damping factor, fluctuating loading pressure and loading torque has comparatively large influence on control properties.
仿真结果表明，系统等效转动惯量和等效阻尼系数的变化以及负载压力和加载转矩的波动干扰，对系统控制性能的影响较大。
The characteristics of steering angle, steering torque and the pressure in cylinder were analyzed when the steering wheel was held or not in the testing.
着重分析了在阶梯路面上汽车液压动力转向系统在方向盘脱手和未脱手的两种工况下方向盘转角特性、方向盘转矩特性和转向动力缸的压力特性。
In this paper, the rotation of cylinder through the action of radiation pressure generated torque based on the ray optics has been investigated.
采用几何光学模型对圆柱体在激光辐射压力的作用下，产生的转动进行了详细地计算。
This paper mainly describes the ener-gy loss and its harm caused by insufficient working flow rate and pressure of torque converter, inclnding the corresponding measures of compensation.
本文着重论述了由于变矩器工作流量和压力不足带来的能量损失及其危害，以及对此所采取的补偿措施。
Crankshaft converts gas pressure from side rod into torque, which ACTS as the driving force and output.
曲轴在内燃机中主要是将连杆传来的气体压力转变为扭矩，作为动力而输出做功。
The system monitors and records the spindle speed, torque, temperature, pressure and leak rate of the seals under test. Trend data is collected, plotted and stored in a database.
该系统可监测和记录主轴转速，转矩，温度，压力和被测试密封圈的泄漏率，并将趋势数据收集，标绘和存储在数据库中。
When the current state, the valve plate and valve seat seal between the drive torque on the valve so that pressure to the valve seat.
当逆流状态时，阀板与阀座之间的密封靠驱动装置的力矩使阀板压向阀座。
During tank's moving, the rubber in the tracked board is suffered the cyclical pressure, rally, torque. It is very easy to fatigue ineffective because of the cyclical power.
坦克履带板着地胶块在坦克的运行过程中，周期性受到压力，拉力，扭转力，很容易因为这些周期性的受力而疲劳失效。
Select the appropriate pressure and torque sensors, develop SCM control circuit and small-signal amplifier, do data acquisition and Processing by PC and multifunctional data acquisition card.
选择适合的压力、扭力传感器，开发单片机控制电路、小信号放大器，应用PC机并配合多功能数据采集卡完成数据采集与处理。
Operation process as the medium pressure is help to open valve, so reduce operating torque.
操作过程由于介质压力是有助于阀门开启的，所以减小了操作力矩。
Operation process as the medium pressure is help to open valve, so reduce operating torque.
操作过程由于介质压力是有助于阀门开启的，所以减小了操作力矩。
应用推荐