The key technique for manufacturing this heat exchanger is the continuous pressure moulding of long plates and welding of thin plates.
较长板片的连续压制成型和薄板片间的焊接是制造该换热器的关键技术。
The production method of as-cast high strength and toughness ductile iron crankshaft for "Shenlong" brand car with high pressure moulding line was finally determined.
在高压适型线生产中，获得铸态条件下生产强韧性神花轿车球铁曲轴的生产工艺。
When the moulding technological test is carried out on the air impulse test moulding machine, the moulding sand employed is the sand used by Nanchang Diesel Factory for high-pressure moulding.
利用气流冲击试验机进行造型工艺试验，使用的型砂为南昌柴油机厂高压造型用砂。
Separation properties of carbon membrane were affected by binder ratio, moulding pressure etc.
炭膜的分离性能与成型压力、粘结剂含量等工艺条件有关。
The effects of carbon content, moulding pressure, and carbon particle size of green body on microstructure and properties of reaction-bonded silicon carbide (RBSC) have been investigated.
研究了反应烧结碳化硅陶瓷的显微组织和性能与生坯碳含量、成型压力以及碳粉粒度的关系。
Sample of porous SiC polycrystals are prepared by solid sintering process under high temperature and normal pressure using moulding SiC powder.
碳化硅粉末经压制成型后，在高温常压下固相烧结制成多孔碳化硅样品。
They shape the plastic into bowls or buckets by moulding it under pressure.
他们将塑料在高压下塑成碗或桶的形状。
Analyses are made for the influence factors of moulding characteristics such as coal type, size, distribution water content, moulding pressure and briquetting rate.
分析了影响成型特性的因素，如煤种、粒度、水分、成型压力和成型率等。
The raw materials, extrusion pressure, pressure holding time and molding temperature during extrusion moulding have great effects on the quality of products.
挤压成型过程中原材料、挤压力、保压时间和成型温度对制品的品质影响较大。
Liquid silicon rubber injection moulding has constant cooling pressure to the cable. It is Low in electricity output while "breathing" together the cable.
液体硅橡胶注射成型对电缆本体有恒定的收缩的收缩压力，与电缆同“呼吸”局部放电最低。
Blow moulding is a process used to make hollow plastic parts which involves heating the material and then forming it into a mould using air pressure.
吹制模制是一种用来制造中空塑料部件的工艺，将材料加热，然后用空气压力使它在模子中成型。
Then they are put into a brick press for moulding after they are stirred, at the same time, pressure about six tons is applied.
搅拌后送入压砖机成型时，同时要选用六吨左右的压力进行施压。
Automatic upper moulding machine can adjust depth according to upper proportion. Change pressure, speed, time, temperature, etc according tomaterial. The upper can get best effect.
自动靴面定型机可视鞋面面积大小调整所需行程深度，依材质特性调整需承受力、下料速度、定型时间、定型温度、下刀顶料压力，使鞋面定型翘度更加完美。
The effects of the content of the dopant, moulding pressure and temperature and the content of oxidant on the conductivity of PANI were studied.
研究了掺杂剂用量、模压压力、模压温度、氧化剂用量对聚苯胺盐电导率的影响。
This paper introduced the new device of injection moulding with keeping pressure. The device was excellent result for the injection of glass fibre reinforced plastics.
本文介绍了一种新型模塑保压装置，采用这种保压装置成型玻璃纤维增强塑料有比较明显的效果。
The beam shape of concrete transfer floor is completely studied. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed.
首先，针对转换层梁模体系及支撑架施工，重点分析了转换层结构现浇混凝土对模板侧压力值及模板对拉螺杆的计算；
Also disclosed is a method of moulding long concrete articles in which an homogenous concrete mixture is subjected to a moulding pressure above (5) bar in the absence of vibration.
还公开了一种模制长混凝土制品的方法，其中在无振动的情况下，使均质混凝土混合料受到5巴以上的模制压力。
Advanced graphite composite is made from graphite and synthetic resin, it is formed by direct moulding process under a definite temperature and pressure.
高性能复合石墨材料由石墨与合成树脂在一定温度和压力下模压复合而成。
Advanced graphite composite is made from graphite and synthetic resin, it is formed by direct moulding process under a definite temperature and pressure.
高性能复合石墨材料由石墨与合成树脂在一定温度和压力下模压复合而成。
应用推荐