CBGJ single high-pressure gear pump. dual two series.
CBGJ高压齿轮泵单。双两个系列。
The product is applied to medium, high-pressure gear pump, ram pump, vane pumps, etc.
产品主要应用于中、高压齿轮油泵、柱塞泵、叶片泵等。
For often work under high pressure gear pump, the working pressure shall be lower than the rated pressure of the pump 1 ~ 2 pressure level.
对于经常工作于较高压力下的齿轮泵，其工作压力应比泵的额定压力低1 ~2个压力级。
High viscosity gear pump does not generate pressure, it is only the output flow. Pressure is low or no pressure, high viscosity gear wheel pump don't inhale the liquid or leakage is serious.
高粘度齿轮泵并不能产生压力，它只是输出流量。压力低或无压力，说明高粘度齿轮泵没有吸入液体或泄漏严重。
High viscosity of the liquid transmission gear pump should be at a lower power consumption, less leakage, larger output under the pressure of the most traffic.
输送高粘度液体的齿轮泵应做到在较低的功耗、较少的泄漏、较大的压力下输出最多的流量。
The synchronization gear pump can reduce the radial and boost the work pressure.
同步齿轮泵能够降低齿轮泵径向力，提高齿轮泵的工作压力。
The interlaced gear pump is designed on the basis of analysing flow and pressure pulses.
本文在分析齿轮泵的流量脉动和压力脉动的基础上，设计出一种错齿齿轮泵。
The pump flow evenly, smooth operation, low noise, high power operation pressure and volume ratio gear pumps, gear pumps than messy layout.
这种泵流量均匀、作业平稳、噪音小、作业压力和容积功率比齿轮泵高、布局比齿轮泵杂乱。
The operating noises of the gear pump are mainly from the perturbations of mass flow rate and the pressure, which result in the error of gear teeth geometry contact during the rotation.
齿轮泵中轮齿啮合几何学上的原因所造成的流量脉动及其相应的压力脉动是产生噪声的主要原因之一。
If the high viscosity gear pump high pressure adjustment, will make the pump running under overload.
如果高粘度齿轮泵的工作压力调整过高，则会使齿轮泵在超负荷下运行。
The manufacturing process for P/M low pressure oil pump gear, conditions of stand testing and technological and economic results have been introduced.
介绍了粉末冶金低压油泵齿轮的制造工艺、台架试验情况及应用的技术、经济效果。
High viscosity gear pump does not generate pressure, it is only the output flow.
高粘度齿轮泵并不能产生压力，它只是输出流量。
The strong points of the compound gear pump are balanced hydraulic pressure of radius, uniform of flow rate, small volume, large displacement and low noise and so on.
它具有径向液压力平衡、流量均匀性好、噪声低、排量大、体积小等优点。
The service life for gear pump is much less than the desired design up to now, which is mainly caused by higher pressure imbalance.
迄今为止，齿轮泵的寿命还远远达不到设计要求，这主要是齿轮泵存在较大的径向不平衡力所致。
Secondly, analyzing statics characteristic of the multi-gear pump demonstrates that radial hydraulic pressure, meshing force and resultant force are balanced on the center wheel.
其次，对多齿轮泵的静力学特性作了分析，证明了中心轮径向液压力、啮合力及总作用力平衡。
The study indicates that the pump can reduce the radial force on the gear and raise the working pressure of the pump. The pump has vast application vistas.
研究表明，该泵可显著降低齿轮泵的径向力，提高泵的工作压力，具有良好的应用前景。
At present, in continuous extrusion processing of micro cellular plastics, the two pressure drop cell nucleation apparatus of the nozzle and gear pump are used.
在连续微孔挤出加工中，当今采用喷嘴和齿轮泵两种快速压降成核装置。
The purpose of this paper is to analyse the causes and process of air-erosion to CB-G middle and high pressure gear-pump and to advance the measures to prevent air-erosion.
本文对中高压CB—G型齿轮泵气蚀发生的原因和过程，应用物理和化学原理进行了分析和探讨，并提出防止气蚀现象的产生应采取的措施。
High viscosity pump is conveying liquid with high viscosity gear pump, should be in lower power consumption, less leakage, under the pressure of large output the most traffic.
高粘度泵是输送高粘度液体的齿轮泵，应做到在较低的功耗、较少的泄漏、较大的压力下输出最多的流量。
For not frequent work gear pump, the working pressure is desirable for the rated pressure of the pump, taking the quality into consideration, it is best to used pressure rated lower 20% ~ 30%.
对于不频繁工作的齿轮泵，其工作压力可取为泵的额定压力，考虑到产品质量不同，最好将额定压力降低20% ~ 30%使用。
In this paper, a detailed analysis is presented for the radial forces of gear pump with expended high pressure area. Some accuracy formulas are given.
本文详细地分析了具有扩大高压区结构的外啮合齿轮泵的径向力和传动扭矩，给出了其精确计算公式。
Pressure is low or no pressure, high viscosity gear wheel pump don't inhale the liquid or leakage is serious.
压力低或无压力，说明高粘度齿齿轮泵没有吸入液体或泄漏严重。
Main products: vessel gear case, hydraulic pressure clutch, hydraulic pressure double and branch driver, timing clutch, reducer, vacuum pump etc.
主要产品有：船用齿轮箱、船用辅机、液压离合器、液压离合分动箱、液粘调速离合器、减速机、真空泵等。
High pressure cleaning pump High pressure cleaning pump, portable or stationary, has two kind of transition devices: transmitting belt or inner-placed gear box.
系列高压清洗泵有移动式、固定式，又有皮带和内置减速器两种。传动型式使用方便，压力高，流量大，运行平稳，安全可靠，清洗范围广。
Gear pump structure simple compact, the manufacture is easy, to maintain conveniently, has the self-absorption ability, but current capacity, pressure oscillation the noise and is greatly big.
齿轮泵结构简单紧凑，制造容易，维护方便，有自吸能力，但流量、压力脉动较大且噪声大。
The relative merits of two kinds of nucleation devices, i. e. quick pressure-relief nozzle and gear pump adopted in the continuous extruder were expounded.
阐述了连续挤出设备中采用的2种成核装置(快速释压喷嘴和齿轮泵)的优缺点。
The relative merits of two kinds of nucleation devices, i. e. quick pressure-relief nozzle and gear pump adopted in the continuous extruder were expounded.
阐述了连续挤出设备中采用的2种成核装置(快速释压喷嘴和齿轮泵)的优缺点。
应用推荐