For the description of the debris behind oblique single plate target perforated by kinetic projectile, an initial armor debris cloud model has been proposed.
针对动能杆式弹大倾角斜撞击靶板产生的靶后破片，建立了其初始破片云数学描述模型，并在此基础上对斜撞击靶后破片特征分布进行了建模。
Puffing gas can reduce the plasma temperature in the scrape off layer (SOL). Injected impurity can increase the radiation power in SOL. Both of them make the heat load on the plate target smaller.
喷气能降低删削层（SOL）处等离子体温度，注入的杂质增加了SOL处的辐射功率，使靶板的负载降低。
A steel or aluminium target plate fitted opposite the sensor serves as a measuring target.
对侧边沿为钢制或铝制平板，作为传感器的被测物体。
Using a plate whose hemisphere reflectivity is known as a standard plate, the lidar scattering cross section (LRCS) and hemisphere reflectivity of a target plate are measured inversely.
在外场用已知半球反射率的靶板作为标准靶板，反演测定目标靶板激光雷达散射截面和半球反射率。
The FE analysis also shows that with properly created model, the penetration process, penetration properties of steel plate by FSP and target damage mode can be simulated very well by using FE method.
有限元分析结果还表明，采用适当的模型，有限元法能较好地模拟破片模拟弹侵彻钢板的侵彻过程、侵彻特性以及钢板的破坏模式。
The simulation results can show plasma parameter distribution characteristics in the area of edge layer, especially the characteristics near the first wall and divertor target plate.
模拟结果能显示边界层区域等离子体参数的分布特性，尤其能显示第一壁和偏滤器靶板附近等离子体参量的分布特性。
The simulation result shows the plasma parameter distributions in the edge layer, especially near the first wall and the divertor target plate.
模拟结果显示边界层区域等离子体参数的分布特性，尤其能显示第一壁和偏滤器靶板附近等离子体参量的分布特性。
The results show that large amount of surface heat load can be removed even by stationary free surface liquid lithium target plate due to rapid evaporation.
结果表明定常自由表面液态锂靶板也可以取出大量表面热负荷。
Based on the experiments, the process penetrating the target plate was simulated by using the method of finite element.
在实验研究的基础上，利用有限元方法模拟分析了弹头侵彻靶板的物理过程。
The purified protein coated on polystyrene plate was used as the target to carry out four rounds of bio-panning.
以此纯化蛋白为靶，采用固体包被法对噬菌体展示随机十二肽库及环七肽库进行亲和筛选。
This method USES laser beam oblique incidence to the test side of plate, and the laser spot of tested plate will be imaged to CCD target surface by industrial video camera.
该方法采用激光斜射到待测钢板侧面上，用工业摄像机将被测板上的激光光斑成像于CCD靶面。
Numerical simulations of the course of the plate blade impacting target with the different angles and the initial velocity were performed based on the finite element model.
建立有限元模型，对平板条叶片以不同角度和初始速度撞击矩形靶板的过程进行了数值模拟。
According to Finite Element Method, the impactor is considered as a discrete mass system in terms of 3D solid element with initial velocity, and 2D shell element is used for target plate.
首先采用有限元法，将撞击体离散成由三维实体单元构成的具有一定初始速度的离散质量系统，对靶板采用二维壳单元离散。
First of all, within the target-oriented in the plate and guide pin sets, and then slide the sleeve nut plate.
首先在垫板内对准导向销和导向套，然后滑入防松套筒板。
Because the utility model adopts the form of electron-acceleration of ion-ion bonding so as to cause ion flow collected by a base plate (a workpiece) is only 10 to 15 percent of target current.
由于本实用新型偏压采用电子—离子加速—离子结合形式，使基板(工件)所收集到的离子流是靶电流的10—15%。
The thermal cycling test of divertor target plate was carried out in the vacuum;
在真空室中用大功率电子束作为热源进行了热疲劳试验。
The thermal cycling test of divertor target plate was carried out in the vacuum;
在真空室中用大功率电子束作为热源进行了热疲劳试验。
应用推荐