The New Jersey job was obtained, I contrived a copper-plate press for it, the first that had been seen in the country.
新泽西州的业务接到手，我为此设计了一部铜版印刷机，这在当地还是首创。
The nickel shim becomes the embossing plate that is wrapped around the embossing cylinder on the foil embossing press.
镍垫片成为压花板，压花铝箔压花按缸周围包裹着。
Most of prepress dept output the plate, they would not know the plate would be printed by which press.
大多数印前部门输出印版时并不知道该印版在哪台印刷机上印刷。
We will be the most preferential prices to provide you with reliable quality of flat-panel curing machine parts and similar specifications of the plate curing press.
我们将以最优惠的价格为您提供质量可靠的平板硫化机配件及同类规格的平板硫化机。
The process of cleaning the rollers, form or plate, and fountain of a press with solvents to remove all ink as required after a day's run, or during a run for ink color changes.
中义在一天工作完毕或更换墨色时，以溶剂清洗辊筒、印版或印刷机的水槽以洗去所残留的印墨。
The process of separating wax from oil by first chilling (to help form wax crystals) and then filtering under pressure in a plate and frame press.
从油中分离石蜡的过程，首先进行冷冻(帮助生成石蜡晶体)，然后用板框式压滤机在压力下进行过滤。
Align the hex plate with the receiver on the head and gently press down until the lock clicks into place (figure 13).
然后将六角形快装板与云台上的对应处对齐，接着轻轻按下直到锁紧(图13)。
The fire accident analysis of press plate filter due to static electricity was made. Its prevention measures were brought forward.
对一起由静电引起的板框式加压滤油机着火事故的原因进行了分析，并提出了防范措施。
This article introduces the design of louver tooling for turret punch press, mainly focusing on the design and calculation of die, punch body and stripper plate.
介绍了多工位数控冲床用百页窗模具的设计，重点介绍了下装凸模、上装镶拼凹模及卸料板的设计和计算方法。
It is showed from the actual examples that the plate shape can be the best with optimizing the press rules to make the shape ratio for every pass equaled.
通过实际算例，优化压下规程可使各道次的板型系数相等，表明板型达到最佳状态。
The plate springs of the spring-loaded clutch press the friction discs together.
弹簧离合器的板簧将摩擦片压紧在一起。
Conventional plating methods are based on the use of an adequate number of anchoring screws to press the plate against the bone with high compressive forces, creating a stable bone-implant connection.
传统钢板固定方法基于采用足够数量螺钉通过高压应力将钢板固定于骨面而产生稳定骨-内植物连接。
In all of the press, pillow as determine a printing plate cylinder and rubber roller lining of fixed base.
在所有的印刷机上，滚枕作为确定印版滚筒和橡皮滚筒包衬的固定基准。
One side of the pressure plate is machined smooth. This side will press the clutch disc facing are against the flywheel.
离合器压盘的一边是光滑的，这边将离合器片朝飞轮方向挤压。
This text elaborates the application of cold-press quenching process in production, applying integrated fixture for heat treatment, of pressed rib armored plate for gun body.
阐述了炮塔体压筋装甲板利用热处理成组夹具，完成了冷压淬火工艺，并在生产中得到应用。
Plastic card, plastic card producing method, hot press plate, and car producing device.
塑料卡，塑料卡制造方法，用于热压的板和制卡装置。
There is great gap between theory research and current development about press plate wood vacuum dryer, especially wood vacuum drying schedule which can not meet the requirement of production.
目前，国内对于压板式木材真空干燥机的理论研究与实际还有很大的差距，尤其是木材真空干燥工艺基准不能适应实际生产要求。
Multiple secondary operation dies to be mounted on a common plate to run in one press whenever possible. (to be determined at pre-engineering launch meeting).
只要可能，复合二重工序模具安装在一个公用的模板上，在同一台冲床中进行冲压。
The mould press prebending adopts involutes types mould and simultaneously fold bending the two edges of plate by steps.
模压式预弯采用渐开线式模具，分步对钢板的两边同时进行折弯。
Position drive plate on the crankshaft's dowel pin and press on to the crankshaft flange.
将传动盘安放在曲轴的定位销上，然后压到曲轴法兰上。
Owing to various kinds of factors, plate & frame filter press will generate side pressure to the fil- terplate in the course of filtering.
板框式压滤机在过滤过程中，由于实际中的各种因素，会对滤板产生侧压力。
When no big-size plate vulcanizing press machine, through design deformation mold, could mold big-size high precision O-shape rubber seal on little plate vulcanizing press machine.
在不具备大平板硫化机及大型加工设备条件下，通过设计加工“变形模具”，在小平板硫化机上生产出大规格、高精度的O型橡胶密封圈。
It introduced the processing technology of cold-press sintering moulding used for processing UHMWPE colorful and porous thin plate.
介绍了用冷压烧结成型法加工超高分子量聚乙烯(UHMWPE)彩色多孔薄板的技术。
The vertically float die block and slide plate of combination movement have been adopted in the die to form a ring part on a single stroke of the press with high productivity.
该弯曲模采用浮动模块和复合运动的滑板，使环形零件在压力机一次行程中成形，工作效率高。
Plate and frame filter press is a kind of universal equipment in cane sugar industry, it is used to filter tiny and sticky substance.
板框压滤机适用于难以分离的细黏性物的过滤，是蔗糖生产企业普遍应用的设备。
The most common, the plate-and-frame press, contains caulked , metal septa and a recessed cake space.
最普遍的是板框式过滤机，有可填充的、金属隔片的和凹显空间滤饼的。
The most common, the plate-and-frame press, contains caulked , metal septa and a recessed cake space.
最普遍的是板框式过滤机，有可填充的、金属隔片的和凹显空间滤饼的。
应用推荐