Now, you can rotate this thin plate about this axis.
现在可以绕着这轴,旋转此盘子。
In the connection design of steel structure, the shear plate with high-strength bolt connection is extensively used at the flexible joint where the beam is connected to the weak axis of the column.
钢结构节点设计中，梁与柱弱轴方向的柔性连接常采用剪力板高强螺栓连接，螺栓群所承受的荷载有竖向力和偏心力矩。
The perfect orientation, the scientists discovered, is for food to point at 3.2 degrees clockwise, a tiny fraction to the right of the vertical axis of the plate.
科学家发现，食物摆放的最佳方位是在顺时针偏右3.2度的位置，也就是在盘子垂直轴稍稍偏右。
The diffracted light intensity on axis of a Spatial light Modulator (SLM) with Multi-level Phase Fresnel Zone Plate (MPFZP) is studied by diffraction optical method.
用衍射光学方法研究了加有多级相位菲涅尔波带片(MPFZP)的空间光调制器(SLM)的轴上衍射光强。
Our first order from Romania is for an 8 channel, 7 axis immersion unit for inspection of aluminium alloy plate .
我们在罗马尼亚的第一个订单是8通道，7轴水浸系统，用于检测铝合金板。
In this paper, a theoretical analysis for the local buckling of the flange plate of the partially encased concrete columns subjected to H-shape steel axis force was presented.
对部分包裹混凝土的H型钢轴压柱翼缘板的局部屈曲性能进行了理论分析。
Objective To evaluate clinical effects of reduction, bone fusion and anterior cervical spine plate internal fixation on the treatment of traumatic spondylolisthesis of the axis (TSA).
目的评价颈前路椎体间植骨钢板内固定治疗创伤性枢椎滑脱的临床效果。
The valve shaft adopts the half axis structure and the valve plate adopts the girder construction.
阀轴采用半轴结构，阀板采用桁架结构。
An adjusting groove, the direction of which is parallel to the axis of the rotating shaft, is disposed on the adjusting plate.
在所述调整盘上设置调整槽，所述调整槽的走向与所述转轴的轴线平行。
The open four-axis CNC system based on PC and motion control card can accomplish the cutting of various-angle welding plate.
并以基于PC和运动控制卡的开放式四轴数控系统实现支管端头的变角度焊接坡口面切割。
The gnomon in the middle is perpendicular to the plate, parallel to the earth's axis, and points to the celestial North Pole (near the north Star).
晷针垂直于晷盘，平行于地轴，指向天北极(北极星附近)。
In this peper the defects of conventional wave plate is analyzed, and the design consideration of a wave plate with titling optical axis are mainly discussed.
本文分析了常规波片的缺点，重点讨论了倾斜光轴波片的设计方法。
The method of tuning is rotating the wave-plate by the axial direction parallel to the optical axis.
调谐的方法是使石英波片绕平行于光轴的轴向转动。
The perfect orientation, the scientists discovered, is for food to point at 3.2 degrees clockwise, a tiny fraction to the right of the vertical axis of the plate.
科学家们发现，完美的方食物摆放方向是顺时针方向3.2度，即稍稍偏离餐盘中轴。
The bearing at the bottom plate center is fixed with the principal axis of the duster.
下盘中间的轴承中以键固定着喷粉机的主轴。
Objective To evaluate clinical results of anterior plate internal fixation in the treatment of traumatic spondylolisthesis of axis (TSA).
目的评价C2、C3椎体间植骨、钢板内固定治疗创伤性枢椎前滑移的临床价值。
The damper plate rotates around an axis rod to control the flow of air through the vent pipe.
这个风挡通过中心轴控制旋转来让通过排气管的空气流动起来的。
The phase delay can be calculated and the placement of the fast and slow axis of the wave plate can be marked after analyzing the curve.
分析实验曲线，可计算出波片的延迟量，同时也可确定波片快慢轴的方位。
The hydraulic pressure revolution axis design thickens the plate, the anti-collision, is not easy to distort.
液压转轴设计加厚板材，抗碰撞，不易变形。
This machine mainly by the rotor, the main axis of the plasma disk, plate device, bearing seat, drive frame, composed of large pulley.
本机主要由转子、主轴、出浆盘、筛板装置、轴承座、传动支架、大皮带轮等组成。
A new 3-axis tactile sensing technique using plane waveguide plate is proposed in the paper. The operating principle and the system constitution of the technique are introduced.
提出了一种新的平面波导三轴触觉传感技术，介绍了其工作原理和系统组成。
This One Axis and Four Pavilions Commemorative Plate is made by authorization of the Bureau of Shanghai World Expo Coordination.
“一轴四馆纪念牌”经上海世博会事务协调局授权制造发行。
In order to adjust the bending Angle, the t type slide seat and bending press plate were used. The adjusting of bending radius was implemented by replacing the adjusting axis of bending radius.
模具采用T形滑座与弯曲角两边的压板调节，从而达到在一定范围内调节弯曲角度的目的，弯曲半径的调节主要是通过更换弯曲半径的调节轴来实现。
In order to adjust the bending Angle, the t type slide seat and bending press plate were used. The adjusting of bending radius was implemented by replacing the adjusting axis of bending radius.
模具采用T形滑座与弯曲角两边的压板调节，从而达到在一定范围内调节弯曲角度的目的，弯曲半径的调节主要是通过更换弯曲半径的调节轴来实现。
应用推荐