To liquefy or reduce to a plastic state by heating; melt.
熔化通过加热变成液体或可塑状态；熔化。
The way of cutting hard brittle material in a plastic state is classified.
对塑性状态下切削硬脆材料的方法进行了归纳和分类。
This paper introduces a new processing think of cutting hard brittle material in a plastic state.
提出了在塑性状态下切削非金属硬脆材料的加工思路。
Meanwhile, halite is also a good cap rock, and would be in plastic state under high temperature and high pressure condition.
盐岩又是良好的盖层，且在高温、高压下呈塑性状态。
The results indicate that it is essential to revise the bolt stress by using the formulas when rock mass is in plastic state.
结果显示，当岩体进入塑性、变形较大时，用推导公式对锚杆变形、应力进行修正是非常必要的。
The peculiarity of this wellbore stability model is to determine whether the wellbore rock is in the critical plastic state rather than elastic limit state.
依据井壁围岩是否达到临界塑性状态而不是弹性极限状态来判断井壁稳定性是气体钻井井壁稳定分析模型的特殊之处。
The method for identification of plastic state of the disk, as well as the approach to obtaining the secant module and transverse deformation coefficient are presented.
提出了轮盘进入塑性状态的鉴别方法、在塑性状态下求出割线模量和横向变形系数的方法等。
Other plastics can be repeatedly reheated to return to the plastic state; they are thermoplastics. Examples of thermoplastic plastics are acrylics, nylon, and polyethylene.
其他塑料可以二次通过再热的方式恢复到可塑性状态，这些是热塑性塑料，如丙烯酸树脂，尼龙和聚乙烯。
In a hot-working process, the metal is brought to the viscous or plastic state by subjecting it to elevated temperature, and by the use of pressure it flows without fracture.
在热加工过程中，将金属升温，使其处于粘性即可塑状态，再加压使其流动而不折断。
The destabilization condition in plastic state, the main causes of wrinkling and the pre ven tion means in the sheet drawing process of tube-shaped parts have been intro duced.
介绍了薄板拉深筒形件的塑性失稳条件，起皱的主要原因及防止措施。
When the load is becoming larger, the soil bearing press capacity will weaken after the soil enters the plastic state, thus the effect of the anchor pile will be little, so it can be neglected.
当荷载不断增大，土体进入塑性状态后，土层承压能力减弱，锚桩的影响将很小，可以忽略。
At halftime I headed back for another round, and this time a lady at the counter asked me to take my New York State driver's license out of the plastic window in the wallet and hand it to her.
中场休息时，我又去买，这次就没那么顺利了，女柜员让我再出示纽约州的驾驶执照，而且要从皮夹的塑料套子中取出来，交到她手里。
The vacuum sealed plastic packs of the fish were sold in New York state and were found to have been uneviscerated before processing.
这些真空包装的食品在纽约州有售，人们发现在竹荚鱼加工处理前没有进行内脏处理。
Unlike compression molding, however, transfer molding includes heating the plastic to a fluid state before it gets to the mold and forcing it into a closed mold using a hydraulically actuated plunger.
与压缩成型，但是，传递模塑包括取暖的塑料流体之前得到国家的模具，并迫使它变成一个封闭的模具采用液压驱动柱塞。
An adiabatic shear band formed along the main shear stress around the penetrated hole is approximately consistent with the direction of plastic deformation slip lines in static state.
弹孔周围的绝热剪切带沿主剪应力方向形成，与静态塑性变形滑移线方向接近，绝热剪切带上不均匀的变形将产生微裂纹和微孔洞。
This technology keeps the casing in an elastic state in the whole thermal recovery process without plastic deformation taking place, and thus resolves the problem of thermal casing failure.
该技术可使套管在整个开采过程中一直处于弹性状态，不发生塑性变形，从而解决了套管热破坏问题。
The material quality and technical requirements of plastic bags shall be governed by the relevant state standards.
塑料购物袋的材质及技术要求由国家相关标准予以规范。
It bases on the classical plastic theory, and the components of wetting deformation under complicated stress state may be determined clearly.
该模型依据经典塑性理论，能够明确指定复杂应力状态下湿化变形的各分量。
Elastic and plastic terminal of vessel, maximum internal pressure that metal liner can't be yielded in the opposite direction and basic condition that vessel works on stable state are presented.
并对压力容器的弹性极限、塑性极限、金属内衬不会产生反向屈服的最大内压以及压力容器在“安定状态”下工作的条件进行了理论分析。
The flow state analysis of the plastic melt in the extrusion die is the basis of the extrusion die design.
塑料熔体在挤出模中的流动状态分析是挤出模设计的基础。
The effect and resilience rule of the plate's plastic deformation and membrane force on the stress state and deformation state are discussed.
主要讨论板壳成形过程中的结构性问题，探讨板料塑性变形、板内膜力对应力状态和变形状态的作用以及回弹规律。
Then plastic flow mechanics are depicted in three aspects as follows: heat transfer, physical state changing and viscoelastic formation.
从传热学、物理状态变化和粘弹形变三方面阐述了微通道热压成形过程中塑料的流动机理。
Establish finite element model, and use elastic - plastic mechanics to discuss stress-stain state of elastic and plastic deformation in cutting zone.
根据正交切削特点建立了有限元模型，应用弹塑性力学讨论了切削变形区的弹、塑性阶段的应力、应变状态。
The analysis and contrast of deformation pattern, state of stress, plastic deformation history, plastic limit load and limit load of elastic buckling are analyzed and contrasted.
最后对三种结构型式的拱顶储罐的变形方式、应力状态、塑性变形历史、塑性极限压力、弹性失稳临界压力进行了分析与对比。
Changle City emerging deer Plastic company Limited is a professional rubber manufacturing company, is approved by relevant state departments of registered enterprise.
长乐市新兴鹿塑胶有限公司是一家专业橡塑制造的企业，是经国家相关部门批准合法注册经营的企业。
A reciprocating screw moves the plastic along this lengthy heating chamber, where the material is melted to a fluid state.
往复螺杆移动塑料沿着这条漫长的加热室，那里的材料融化到流体状态。
Hegde's claims are backed up by the Karnataka State Pollution Control Board, which conducted several tests to ensure the bags contained no plastic before approving their use.
Hegde的主张得到了卡纳塔克邦污染控制委员会的支持。他们对这种袋子做了一些测试以确保不含塑料成分，然后才能通过使用。
The current state and the existent problem of AgO-Zn secondary battery case, as well as the poor effects of plastic case on battery performance were introduced in this paper.
介绍了目前锌银二次电池壳体材料的现状和存在的问题，以及塑料材料壳体对电池的不良影响；
The current state and the existent problem of AgO-Zn secondary battery case, as well as the poor effects of plastic case on battery performance were introduced in this paper.
介绍了目前锌银二次电池壳体材料的现状和存在的问题，以及塑料材料壳体对电池的不良影响；
应用推荐