The simplified elastic-plastic analysis was used for the thermal expansion loading.
事故工况下温度载荷对设备的影响采用了简化弹塑性分析的方法。
This paper presents the elastic plastic analysis results of mono strand anchor head by the finite element method.
本文采用有限元方法给出了单孔锚具的弹塑性分析结果，分析了摩擦系数对锚具性能的影响。
The corresponding elastic-plastic solutions are also obtained by the-engineering method of elastic-plastic analysis.
并用弹塑性分析的工程方法得到相应的弹塑性解。
In terms of the calculating theories of the composite steel-concrete beam, the elastic analysis and the plastic analysis are expounded systematically.
在组合梁的计算理论中，作者分别详细地阐述了组合梁的弹性分析和塑性分析理论。
Based on plastic analysis and non-linear finite element analysis, the structure's load-bearing capacity under secondary internal forces is calculated and certified.
利用塑性极限分析和非线性有限元分析方法计算并验证了结构在考虑次内力作用时的极限荷载。
At the same time, precise structure elastic-plastic analysis method created advantage for the performance-based design method, an advanced aseismatic design method.
同时，精确的结陶弹塑性分析方法也为先进的抗震设计方法——性能抗震设计法创造了有利条件。
By comparing the ways of plastic analysis, the plastic moment coefficient and load coefficient are used to illustrate the collapsing load formula of mobile-structure.
本文通过对塑性分析方法比较，采用了塑性弯矩系数和荷载系数来表达机构破坏荷载公式。
Next, on the basis of the transient-state thermal analysis, the thermal elastic-plastic analysis of the thermal-structure couple is obtained in the axial symmetry loads.
其次，在喷管轴对称模型瞬态热分析的基础上研究了轴对称载荷下热—结构耦合场的应力分析。
The obtained transient temperature field can represent the basic characteristics of the real welding process and can be used as the foundation of thermal elastic-plastic analysis.
该温度场能够反映实际焊接过程的基本特征，可以作为焊接过程热弹塑性分析的依据。
Heat-fluid-solid coupling and contact thermo-elastic-plastic analysis was carried for a certain turbine blade-disc, and the stress and strain-time course was obtained in this paper.
采用随机有限元方法， 针对某燃气涡轮盘-片进行了热流固耦合及接触热弹塑性分析，得到了随机应力应变响应；
This paper presents a simplified plastic zone method with consideration of the influences of the plastic zone length on the stiffness matrix for elastic-plastic analysis of steel frames.
对于杆件单元，本文采用了一种变刚度的杆单元模型，建立了考虑塑性铰分布长度影响的构件单元刚度矩阵。
During the past decade advances in computerisation have resulted in major changes in space structure design, and int he analysis of their stability and plastic behaviour.
过去十年中运用计算机方面的进步，使空间结构在设计、稳定分析以及塑性性能等方面都有了很大的变化。
The metallurgical structure and fracture morphology of the tensile specimens were investigated with SEM and metallurgical analysis, and the static tensile plastic deformation mechanism was researched.
利用扫描电镜断口分析及金相分析技术，分析了材料拉伸试件断口形貌及金相组织，初步探讨了材料的静态拉伸塑性变形机理。
The design process of plastic wye injection mould is stated in detail from the analysis of plastic part , the analysis of the process and the design of the struction.
从塑件分析、工艺分析、结构设计三方面详细阐述了常见塑料三通注射模的设计过程。
Be responsible for mass production of rubber, plastic parts and non-ferrous meta analysis and solving quality problem.
负责批量生产过程中橡胶、塑料件及其非金属零件的质量问题的分析、解决。
It holds a wide tube that will route my exhalations into plastic bags for analysis.
在上面一支大口径管，会把呼出的气体收集到塑料袋中用来分析。
Plastic limit analysis is a physical nonlinear Problem.
塑性极限分析是物理非线性问题。
In this paper the reason and criterion of the application of the model to plastic limit analysis are discussed, and an algorithm of computing plastic limit load is given.
文中讨论了该模型适用于全塑性分析的机理和判据，还设计了一个确定塑性极限载荷的算法。
Since normal plastic theory is too complex, the membrane theory and the semi-membrane theory are adopted to establish the equilibrlm equations in plastic limit analysis.
鉴于有矩理论的复杂性，本文在作极限分析时，采用了无矩理论和半无矩理论的平衡方程分别作为中短壳和长壳的平衡方程。
It is shown by the instance of criticality analysis of plastic extruder that the proposed method is effective for evaluating the equipment criticality.
将其应用到塑料挤出机的重要度分析中，结果表明，该方法对设备重要度的确定是有效的和实用的。
The reacting status between wheat straw, adhesive and plastic can be known through the analysis of hot reaction.
通过热反应分析，可以了解麦秸与胶粘剂及塑料之间的反应状况。
By using scan electron microtechnique and thermal analysis, wood plastic composite mechanism is studied.
采用扫描电子显微技术和热分析对木塑复合机理进行研究。
Do mold flow analysis of plastic parts for improving design and manufacturing.
对塑料件产品进行模流分析以改进设计和制造过程。
It is theoretical basement to apply further for practice thixotropic plastic forming technology analysis.
为在实际触变塑性成形工艺分析中的进一步应用奠定了理论基础。
The elastic plastic buckling analysis is completed on bucking load and buckling mode of thin wall cylindrical shells fully filled with liquid under axial compression.
对充满液体的薄壁圆柱壳经受轴向压缩时的屈曲载荷和屈曲模态进行了弹塑性屈曲分析。
The finite strip method in structural analysis has been extended, and elastic-plastic large deformation spline finite strip method based on the Updated-Lagrange method (U.
拓展了结构分析有限条法，基于固体力学有限形变理论的更新拉格朗日法（U 。
It is important to plastic deformation analysis for we to understand correctly the geometrical form and properties of yield function of sintered powder materials.
正确认识粉末烧结材料屈服函数形状和性质，对于其塑性变形分析有重要意义。
The plastic limit analysis is applied to the unstable fracture load.
对失稳断裂载荷进行了塑性极限分析。
The plastic limit analysis is applied to the unstable fracture load.
对失稳断裂载荷进行了塑性极限分析。
应用推荐