The top-down design methodology is used to realize the PCI bus controller.
采用自上而下的设计方法，实现了较困难的PCI总线控制器。
The PCI Bus Controller IP is part of the IP library of Aviation Microelectronic Center.
该文介绍的PCI目标设备总线控制器的IP设计就是航空微电子中心建库工作的组成部分。
The design of the PCI bus in the interspaced ordonnance, and the realization of the sequence state machine in the PCI interface controller is given.
给出了PCI总线配置空间的设计以及PCI接口控制器中时序状态机的实现。
PCI target interface controller design with FPGA is proposed. And the realization of the complication of the access sequence to the BUS interface controller is expressed by sequence state machine.
给出了一种基于FPGA实现PCI总线目标模块接口控制器的设计方案，用时序状态机来实现总线访问操作复杂的时序。
The DMA controller supports two separate methods for handling legacy DMA via the PCI bus.
南桥DMA控制器支持二种方法经由PCI总线来处理传统的DMA，。
The PCI bus is an important component for our access problem we face because the controller will most likely reside on the PCI bus (if not, its an ISA controller and those should be extinct by now).
PCI总线是一个重要的组件对于我们面临的访问问题因为控制器最可能在PCI总线上(如果不是，它是IS A总线而且现在应该被废除)。
The FSM model of target PCI bus interface controller is then provided based on PCI bus operation timing.
根据PCI总线操作时序，提出了从设备接口控制器的有限状态机模型。
In this research, the design of PCI bus target controller is mainly discussed.
在本论文的研究中，重点分析了PCI总线目标设备控制器的设计。
Difficulty of system Extending and transplant are found by means of PCI (Peripheral Component Interface) bus motion controller or PC (Programmable controller).
系统的扩展和移植难度发现的PCI(外设组件接口)总线运动控制器或PC(可编程控制器)的手段。
In this article, to carry the 6-axis motion controller out, a method of using PCI special interface chip PCI9052 to be a interface bridge of PCI bus and DSP (TMS320LF2407), was introduced.
文章介绍了一种采用PCI专用接口芯片pci9052作为PCI总线与DSP (TMS320 LF 2407)的接口桥接器，实现6轴运动控制卡的硬件设计方法。
The author designed a GPIB controller based on PCI bus.
笔者设计的GPIB控制器采用PCI接口总线来实现和PC机的联结。
The design combined the laser marking technology with PCI Local Bus in a laser marker controller card, which plays an important role in a computer controlled laser marker system.
本文完成了采用计算机控制模式的基于PCI总线的激光打标系统的控制卡设计。
The design of a laser marker controller card based on PCI bus, including hardware development and drive program, is discussed in the paper.
论文从硬件和驱动程序两个方面对基于PCI总线的激光打标控制卡进行了研究，并进行了实物的设计。
The design of a laser marker controller card based on PCI bus, including hardware development and drive program, is discussed in the paper.
论文从硬件和驱动程序两个方面对基于PCI总线的激光打标控制卡进行了研究，并进行了实物的设计。
应用推荐