• Define PCB layout instruction for power electronic circuit.

    功率电路的印制板设计方案。

    youdao

  • The author illustrates antijamming technical ways and measures by analyzing the design principle of power wire layout, PCB design integrality, rational wire layout and mode of metal screen.

    通过对电源布线设计原则、PCB设计中完整性原则、合理的布线规则、金属屏蔽罩法的分析,阐述了抗干扰的技术方法和措施。

    youdao

  • Thus, the power trace of the PCB is simplified in structure, thereby reducing EMI radiation noise.

    因此,PCB的电力轨线的结构被简化,从而降低emi辐射噪声。

    youdao

  • The power lines that supply the GFCI with power are also coupled to the circuits on the PCB (122) to disconnect power to those circuits of the GFCI that trips due to faults or tests.

    向GFCI提供电源的电源线路也与PCB(122)上的电路连接,以切断由于故障或测试而跳闸的GFCI的那些电路的电源。

    youdao

  • PCB power supply made in our Company applies for fully new power supply operation and monitor electric circuit; it features big redundancy and assures reliable operation for power supply.

    我公司生产的PCB电源采用了全新的电源运行及监控电路,冗余量大,可以保证电源可靠运行。

    youdao

  • The second substrate includes a power plane deposited at a position of a component mounted to the printed circuit board (PCB) to transmit power to the component.

    第二基板包括电力平面,该电力平面安置在组件的被安装到印刷电路板的位置处以向组件传输电力。

    youdao

  • The elongation and throwing power are important target in PCB plating.

    镀层延展性和深镀能力是评价PCB电镀能力的关键指标。

    youdao

  • The general PCB design steps of the switch power supply and an example were given in this paper.

    本文给出了开关电源PCB设计的一般步骤,并给出实例。

    youdao

  • The design rules and observing proceedings are presented from the layouts, wires placing and grounding of the printed circuit board (PCB) aiming at the EMC design of switch power supplies.

    针对开关电源印制电路板的电磁兼容性设计,从PCB的布局与布线、接地等方面提出设计原则及注意事项。

    youdao

  • At last the article proposes the designing strategy of board-level power distribution system, analyze the principle of decoupling, the method of choosing decoupling capacitors and their PCB designing.

    文章最后提出了板级电源分配系统的设计策略,详细分析了去耦电容的原理,并介绍了去耦电容选取原则和PC B设计方法。

    youdao

  • After studies on basic theory and harm of signal traversing a power gap, provide measures of mixed-signal PCB design.

    课题中介绍了信号跨电源分割的基本原理,仔细分析了信号跨电源分割造成的危害,研究了数模混合pcb的设计方法。

    youdao

  • Shorts may cause a PCB to fail other tests and may damage the tester or the board under test if you must apply power to the board.

    短路可能导致印刷电路板不能通过其它测试,在对电路板上电后,会损坏测试设备或电路板。

    youdao

  • Multek is a large PCB works affiliated to Flextronics, and United Power is the subsidiary of Unimicron, the world's largest handset PCB producer, which supplies PCB for Nokia and Motorola via Foxconn.

    超毅科技是伟创力旗下PCB大厂,联能则是全球第一大手机PCB厂欣兴的子公司,通过富士康供货给诺基亚和摩托罗拉。

    youdao

  • Multek is a large PCB works affiliated to Flextronics, and United Power is the subsidiary of Unimicron, the world's largest handset PCB producer, which supplies PCB for Nokia and Motorola via Foxconn.

    超毅科技是伟创力旗下PCB大厂,联能则是全球第一大手机PCB厂欣兴的子公司,通过富士康供货给诺基亚和摩托罗拉。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定