According to Forbes, Bartz 'transformed Autodesk from an aimless maker of PC software into a leader of computer-aided design software, targeting architects and builders.'
《福布斯》杂志这样写道：巴茨“将Autodesk从一个漫无目的的电脑软件制造商转变成为电脑辅助设计软件的领头羊，瞄准建筑师和建造商。”
And then, the design of software in PC and communication protocol between PC and temperature logger are introduced.
然后，介绍了上位机软件设计以及上位机与温度记录仪之间的通信协议设计。
Chapter three and four expound the design of hardware system and recording software on PC of the automatic test system in detail.
第三、四章详细阐述了篮球专项自动测试系统的硬件系统设计和PC机记录软件的设计。
One kind of stepping motor control card based on ISA bus of PC which achieved multi-spindle linkage control is introduced, its principle and design of hardware construction and software are discussed.
介绍了一种基于PC机的IS A总线步进电机控制卡，实现多轴联动控制，讨论了其工作原理和硬件结构设计、软件设计。
Develop the PC application software according to the requirement of machine project, assuring software design quality.
按照项目输入的要求，开发符合要求的PC应用软件，保证软件设计质量。
Then, the software design of the embedded motion controller which based on the PC/104 bus is analyzed.
再次，论文分析了基于PC/104的嵌入式运动控制系统的软件设计。
To counter the logic program design of PC, this paper expounds some software design methods.
针对其逻辑程序设计，概述了数种软件设计方法。
Summary of the Design and Implementation of PC-based crossover, the matching of hardware, software, the preparation and debug.
简要设计和实现了基于PC的分频器，从硬件的选配，软件的编写和调试。
This paper presents the realization on serial communication of AT89C52 SCM and PC, including hardware structure and software design.
本文介绍了AT 89 C52单片机与PC机之间串行通讯实现，包括硬件结构及软件设计。
Introduces the process of the test and the control requirements and discusses the design for the hardware and software of the PC system.
介绍了检测台的工艺流程及控制要求，对PC自动控制系统的硬件及软件设计作了充分的讨论。
This paper introduces PC control approach of joint motion of manipulator. This approach includes driving of stepping motor, interface design of hardware circuit and software programming.
介绍一种机械手关节运动的PC机控制方法，它包括步进电机的驱动、硬件接口电路的设计、软件的编程方法。
This dissertation studies the design and realization of a PC-based integrated software system for structure health monitoring.
本文主要研究了基于pc机的面向结构健康监测的集成软件系统的设计与实现。
Through describing communication function of VB and HART protocol commands the design method of PC configuration software based HART protocol is described in detail.
通过对VB通讯功能和HART协议命令方式的描述，详细介绍了基于HART协议的PC组态软件的设计方法。
CAD system software is developed based on hardware design of flexible fixture system. This system runs on an IBM PC microcomputer.
CAD系统软件的开发是以柔性夹具系统硬件设计为基础，该系统在IBMPC微型计算机上实现。
The design of the software includes three parts as following: the network communication between PC and controller, NAT9914 firmware and DLL (dynamic link library) program.
软件部分的设计共包括三大部分：PC机与控制器间的网络通信机制，NAT9914固件程序以及动态链接库程序。
This thesis gives us a dairy cow precision feeding system based on PC and SCM, discusses the design of its hardware and software.
开发了由PC机为管理平台基于单片微机控制的奶牛精量饲喂系统，介绍了系统的硬件、软件设计等方面的问题。
The configuration software is divided into PC software and Single Chip Micyoco software. The modularization design idea is adopted in this paper.
该组态软件分为PC机软件和单片机软件两个部分，这两个部分都采用模块化设计思想。
It gives a detailed introduction about the design of system hardware, MCU software and management software running on PC, especially gives an analysis of the key technique for this system.
对系统的硬件结构、MCU控制软件以及上位机管理软件的设计方法进行了介绍，并对其中的关键实现技术进行了分析。
The principle and theory of our design is discussed chiefly. What is elaborated in the paper is the hardware and software design of intelligent relay and PC monitor node.
论文中详细叙述了设计的理论依据，介绍了可通信低压开关电器节点和监控PC节点的硬件设计和工作原理以及相关的软件程序设计思路和编制方法。
The design idea of Automatic Test Equipment on PC is introduced firstly, and the realization technique of hardware and software is discussed chiefly.
首先介绍了基于PC的自动测试仪的设计思想，重点分析了测试仪的硬件及软件的实现方法。
Then this paper elaborates software and hardware design of the vehicle recorder system. System includes the GPS data collection, GPRS part, display and communications with PC etc.
然后本文详细论述了车载记录仪的硬件设计及软件的总体设计，主要包括GPS定位数据采集、GPRS模块的数据接收和发送、数据的显示及与PC机的通信等部分的设计。
Responsible for Similar Tablet PC products software design, code implementation and maintenance.
负责类似平板电脑产品的软件开发，代码编写和维护。
The main point of the subject is to process the uplink and downlink communication by Industrial PC with special software, that is, to design and implement a special gateway for the SCADA system.
本课题的主要任务是通过工控机和专用软件来实现中小水电站计算机监控系统的上下行通信处理，即设计并实现用于现场网络的专用网关。
This article puts forward a design in which NC system is operated by LTP of PC and as well describes the way to design its software and hardware.
文章介绍了一种不添置任何硬件直接利用PC并行口控制的数控系统的设计，并说明了系统的软、硬件的设计方法。
In order to transfer the algorithm to DSP and apply to homing head on the missile at last, the design idea of software and the transfer process of algorithm from PC to DSP are proposed.
提出了将目标自动识别与跟踪算法移植到DSP上，以便用于弹上导引头的软件设计的思路和方法。
This paper describes the basic design principle of automatic measure and control system. Which is compatible with PC BUS standard. technology of error processing as well as feature of software design.
本文主要介绍PC总线标准兼容的自动测试、控制系统的基本设计原理、误差处理技术和系统软件设计特征。
The design of hardware and the software has been given as well as the communication plan between PC and 48 PIC SCMs.
文中给出了系统的硬件设计和软件设计以及PC机与48台PIC单片机的通讯方案。
The way to realize serial communication between PC and the microcontroller 80c196 is discussed. RS-485 converted circuits and the design method of communication software are introduced.
介绍了如何在PC机与80c196单片机之间实现多机串行通讯，RS- 4 85转换电路及相应软件的设计方法。
The hardware and software design principle for real-time data acquisition and processing of an acoustic positioning system using IBM/ PC and relavent interface technique are described in this paper.
本文主要介绍用IBM/PC及接口技术，实现声学综合定位系统实时数据采集及处理的软硬件的设计思想。
A monitoring and control system composed of S7 - PLC and Industrial PC for cement dry mixing device and its design and implementation on software and hardware are introduced in detail.
较为详细地介绍了一个由S7-PLC和工业PC组成的油井水泥干混装置监测、控制系统及其软、硬件的设计与实现。
应用推荐