Differing from previous studies, the new method was derived from the idea of motion of moving trihedron along a predesigned path of contact on the predesigned (theoretical) tooth surface.
与以往的齿面加工方法不同，在新的齿面展成方法中，齿面展成运动是在沿预定接触迹线的曲面活动标架下设计的。
For bow hard grounding, damage path will go toward the side of ship hull, and the contact between the ship and the rock will change gradually from intense impact to lateral press and slip friction.
对于船艏高能搁浅的情况，损伤路径会向船体外侧偏离，船舶与礁石之间的接触由剧烈的冲击逐渐过度到侧向挤压和滑动摩擦；
Even though the contact appeared inadvertent, it did change the path of the ball and the defender had no business flapping his arms around like that.
尽管联系，但它确实改变出现夹杂着球的路径和后卫没有生意拍打他的双臂。
This presents a tortuous flow path to ensure intimate contact of the impurities on the surfaces and within the pores of the carbon.
该过滤器可提供一条曲折的流路，确保对表面或以及在碳毛孔内部的杂质彻底清除。
It appears that the neck and the radial degrees of freedom might both be hampered by an inner potential barrier on their path between the contact configuration to the compound nucleus.
结果显示，在重核从接触到复合核形成的过程中，颈部自由度和径向自由度可能会同时遇到由于内侧位垒引起的熔合阻止。
And give out the unified optical path, Newton's ring radius and convex lens curvature radius measurement formula of non - contact type, simple cutting type and tangent type Newton's Rring.
并给出了非接触式、浅近切割式及相切式牛顿环的统一的光程差，牛顿环半径及凸透镜曲率半径测量公式。
With the brief description of the basic principle of air-coupled non-contact ultrasonic testing, the factors affecting the whole signal path losses of air-coupled ultrasonic testing are deduced.
介绍了空气耦合非接触式超声检测技术基本原理，推导了该技术中信号传输衰减理论构成因式。
Secondly, the meshing path of the contact point of SCMW is deduced based on the meshing function of space curve and the space coordinate transformation.
其次，本文在前期研究建立的空间曲线啮合方程基础上，结合空间坐标变换，推导出空间曲线啮合轮的啮合轨迹；
See Section 21. 9.2 revised June 11, 2008 9.3 An identified grounding contact, or grounding-conductor path through a device shall be of plated or unplated copper or copper-based alloy. Exception No.
第9.2节于2008年6月11日修订9.3一个通过一器件的确定的接地接触件或接地导线通路应该用电镀的或不电镀的铜或铜合金制成。
Equations for describing the tooth surface of a face-gear were established, and the contact path was formed by differential geometry and meshing theory.
推导了双圆环面包络环面蜗杆磨齿啮合界线方程及其与相配蜗轮啮合的啮合界线方程。
Equations for describing the tooth surface of a face-gear were established, and the contact path was formed by differential geometry and meshing theory.
推导了双圆环面包络环面蜗杆磨齿啮合界线方程及其与相配蜗轮啮合的啮合界线方程。
应用推荐