An emerging threat, first outlined by Amit Klein in a paper in 2004, is the blind XPath injection attack (see Resources).
最近开始出现的一种威胁(最初由AmitKlein于2004年在一篇论文中概述)是XPath盲注攻击(请参阅参考资料)。
This paper describes an imperfect pulse injection stimulus-response technique to study the axial mixing in the extraction column.
本文以非理想脉冲注入的扰动-响应技术，进行萃取柱轴向混合的研究。
The foreign research and application situation of Cuttings re-injection technology is summarized in this paper.
对国外钻屑回注技术研究与应用情况进行了总结。
The paper analyzes the reason for more power consumption of conventional dual vane pump system set in model XS—ZY—125 plastic injection forming machines.
本文针对XS—ZY—125型塑料注射成型机，分析了现行通用的双联泵供油液压系统耗能大的原因。
Owing to space constraints, this paper introduced only NIRVANA injection screw air compressor characteristic.
由于篇幅的限制，本文仅介绍NIRVANA喷油螺杆空压机的特点。
This paper introduced the electronic clock back of the injection mold design process.
本论文介绍了电子钟后盖的注射模设计过程。
The application of the grey relative analysis method and grey forecast method to injection development oil field is presented in this paper.
本文主要探讨了灰色关联分析方法和灰预测方法在油田注水开发中的应用。
Molding method, process, and equipment of injection molding of molding compound had been discussed in this paper.
论述了模塑料注射成型的方法、工艺、设备和模具设计方面的问题。
The micropipette puller system designed in the paper can fabricate good cell injection pipette with high stability.
设计的拉针仪系统稳定性高、重复性好，能够拉制出符合要求的注射针。
The Paper introduces the application of flow injection analysis method to automatic analysis and the flow injection analysis method in the standard analysis methods of waste water and American water.
介绍了流动注射分析法在自动分析方面的应用及美国水和废水标准分析方法中的流动注射分析法。
In this paper, the control problem of electromagnetic actuator in electronically controlled diesel fuel injection system is investigated.
针对柴油机电控喷油系统磁电式执行器的控制问题进行了研究。
Re-injection and discharge technology of oilfield wastewater were reviewed in the paper.
综述了各项回注水和外排水处理技术的优势和不足。
The optimization of multilayer OLED is discussed in this paper, especially the optimization of the thickness of hole injection layer.
还进行了多层结构OLED性能的优化，着重进行了空穴注入层厚度的优化。
In this paper, the benzylpenicillin content in procaine benzylpenicillin injection was determined by HPLC.
采用HPLC法测定了普鲁卡因青霉素注射液中青霉素的含量。
A knowledge based injection mold design system (KIMDS) is introduced in this paper.
介绍了一个基于知识库的注塑模设计系统KIMDS。
In this paper, a new control system of an electro-hydraulic fuel injection advancer is presented and its dynamic mathematical model is developed.
本文提出了一种柴油机供油提前角电液调节系统，建立了动态数字模型。
The paper introduces in detail the longitudinal injection ventilation design for the Wushishan Tunnel, which may be used as reference for the ventilation design of other highway tunnels.
本文详细地介绍了乌石山隧道纵向式射流通风设计，可供设计人员在进行其他公路隧道通风设计时参考。
This paper reports acupuncture and point injection therapy for lumbago.
本文报导了针刺配穴位注射治疗腰腿痛的疗法。
The paper has discussed the application of the artificial intelligence technology in virtual injection molding system.
本文探讨了人工智能技术在虚拟注射成型系统中的应用原理和方法。
This paper introduced the CAE for injection molding, discussed the methods to optimize manufacturing technology and parameter of mould design with computer.
本文介绍了注塑模具CAE，论述了用计算机优化制造工艺和模具设计参数的方法。
The optimization theory and method combined with variable frequency speed regulation technology is applied in this paper to realize efficiency optimization in water injection pumping stations.
利用最优化原理与方法结合变频调速技术实现注水泵站效率优化控制，以满足油田生产节能降耗的需要。
A new theory about minority carrier injection into polysilicon emitter has been proposed in this paper.
本文提出了一种新的多晶硅发射区少数载流子注入理论。
This paper provides an overview of the clinical application of Huangqi injection.
仅将近年来黄芪注射液临床应用作一简要综述。
Because it can not predict the future index, this paper combine the injection-production-curve method with HCZ model, find the method of predicting steam injection and heavy oil production.
鉴于其不能对未来进行预测，提出了应用注采曲线法同hcz模型相结合对现场注入蒸汽及稠油产量进行预测的方法。
Objective:This paper presents a study of therapeutic efficacy of oromaxillary hemangioma by local injection with PYM.
目的：探讨平阳霉素治疗口腔颌面部血管瘤的效果。
Molding process, equipment and die of thermosetting plastics for injection molding discussed in the paper.
论述了热固性塑料注射成型的方法、工艺、设备和模具设计方面的问题。
Nowadays, popularizing and applying CAD/CAM technology is an advanced subject. This paper emphatically introduces injection mould design of flagpole coor and CAD/CAM process of its mould parts.
推广应用CAD/CAM技术是当今先进的研究课题。本文着重介绍插旗杆座的注塑模设计及模具零件的CAD/CAM过程。
Controlled hole injection LIGBT (CI LIGBT) is proposed in the paper, which can effectively control the hole injection with high anode voltage, and its latch up free characteristics can be improved.
本文提出空穴注入控制型横向绝缘栅双极晶体管(CILIGBT)，可有效控制高压下阳极区空穴注入，提高器件的抗闩锁性能。
This paper introduced the injection mold design of the Polyurethane elastomer.
介绍聚氨酯弹性体的注塑模具的设计。
This paper introduced the injection mold design of the Polyurethane elastomer.
介绍聚氨酯弹性体的注塑模具的设计。
应用推荐