The effects of parameters on the properties of oxide film were studied.
分析研究了各工艺参数对膜层性能的影响。
The Biological properties of titanium implant depend on its surface oxide film.
钛植入体的生物学性能取决于其表面氧化膜的表征。
The oxide film composition of burnt surface has been discussed by means of XPS.
并应用XPS对烧伤表层氧化膜组份进行了探讨。
OBJECTIVE To study the preparation method of zinc oxide film and quality control.
目的：探讨复方氧化锌涂膜剂的制备及质量控制方法。
The ageing characteristics of sealed oxide film at normal temperature are studied.
通过试验，研究了常温封孔氧化膜的陈化特性；
Black oxide film was prepared on alloy structural steel by electrochemical method.
采用电化学的方法在合金结构钢表面形成一层黑色氧化膜。
All renascent oxygen is consumed for oxidizing metal anode to form metal oxide film.
当形成足够厚的氧化膜后，阳极的氧化速度减慢，阳极表面才析出氧气。
Material oxidation, such as oxidation spot, serious after heat treatment of oxide film.
素材氧化严重，如氧化斑，热处理后氧化膜。
A new green sealing process of anodic oxide film of aluminum alloy was studied in this paper.
本文研究了一种铝合金阳极氧化膜新型的绿色封闭工艺。
Objectives: To study the oxide film of pure titanium implant material treated by anodic oxidation .
目的：研究阳极氧化对纯钛种植材料氧化膜的影响。
The oxide film formed at the duty cycle of 10% has a maximum thickness and best section morphology.
当占空比为10%时，得到最大的氧化膜厚度和最佳的氧化膜截面形貌。
The process was easy to operate with wide range and no pollution, and produced oxide film was good.
该工艺操作简单，工艺范围宽，无污染，所得膜层性能好。
The anode oxide film has a very strong effect on the performances of aluminium electrolytic capacitor.
阳极氧化膜是电解电容器的工作介质，其质量的优劣直接影响着铝电解电容器的性能。
AES analyses of the oxide film and Auger chemical depth profile of the oxide film have been performed.
对氧化物进行了AES分析，得到了元素的深度分布。
SEM and EPM results indicate that cracks form at edges and corners of LY12 aluminum alloy's oxide film.
通过扫描电镜和电子探针发现，LY12型铝合金棱角部位阳极氧化膜产生了裂纹。
Data and programs are stored as electromagnetic charges on a metal oxide film coating the mylar plastic.
程序和数据是以电磁荷的形式存储在聚脂塑料外面包着的金属氧化胶片上。
The intermedium pickling and oxidation annealing can greatly reduce the carbon content in the oxide film.
铜管脱脂，氮气保护退火对降低氧化膜中碳的含量无明显效果。
Sper-clean-up capacity of the oxide film to remove the width continuously adjustable, bright weld appearance.
超强清理氧化膜能力，清理宽度连续可调，焊缝光亮美观。
The key of the manufacturing process of anodic oxide film of aluminium wire is the continuous anodic oxidation.
氧化铅丝生产过程中最关键的工艺是连续阳极氧化。
Immediately below the oxide film and often mingled with it in an intricate way is the true surface layer of the metal.
氧化膜的下面就是真正的金属表层，氧化膜常常与金属表面层以复杂的形式混合在一起。
These tiny semiconductors inject electrons into a metal oxide film or "sensitize" it to increase solar energy conversion.
这些微小的半导体把电子注入到金属氧化物薄膜中，或者说把它“敏化”，从而增强太阳能转换。
This indicates that the problem probably lies in a thin oxide film that forms on contacts and breaks down whenever moved.
这表明，问题可能在于薄氧化膜形成的接触和分解时，感动。
The design principles of indium tin oxide film (ITO) applied to antistatic for optical solar reflector (OSR) have been studied.
对氧化铟锡(ito)薄膜在光学太阳反射镜(osr)抗静电放电设计中的应用进行了研究。
The method, called Atomic level Deposition, coats silver objects with a protective oxide film in layers just a single atom thick.
这种方法被称作“原子级的沉积”，即在银器表面覆盖氧化物保护层，这层氧化物仅有一粒原子那么厚。
The structure and chemical compositions of the surface oxide film were investigated by XRD and Auger electron spectrometry (AES).
利用X射线衍射(XRD)和俄歇电子衍射(AES)观察了表面膜的化学成分及结构。
Phase analysis shows that the distance of crystal face of WC increases and oxide film of Y forms on the surface by Y ion implantation.
相分析表明，离子注入使WC晶面间距增大，稀土元素Y的注入在材料表面形成了Y的氧化物膜层。
The assumption is made that if there is no detectable free iron, the metal surface is clean enough for a uniform oxide film to develop.
假定如果没有探测到游离铁，则金属表面就是足够清洁以形成均一的氧化物膜的。
An organic phosphor has been impregnated in the micropores of an anodic oxide film on aluminum to produce a fluorescent aluminum board.
为制造具有荧光的铝板，在铝阳极氧化膜孔内浸渍有机荧光物质。
The defects of the needle-shaped hole and narrow white threads on the strip surface have close relationship with oxide film of work roll.
工作辊表面氧化膜状态与带钢表面氧化铁皮细孔及小白条压入缺陷的产生有密切关系。
The main defects of laser spot welding of aluminum are crater, hot crack and porosity which created by oxide film and keyhole instability,.
焊点中存在的主要缺陷是气孔，表面下塌，热裂纹，其中气孔主要为氧化膜气孔和匙孔不稳定形成的气孔。
应用推荐