A compact output switch for a water pulse forming line (PFL) e-beam accelerator was designed.
介绍了一种水介质脉冲形成线强流电子束加速器的输出开关的设计和实验结果。
Output switch module technology indicators, load it with different types are closely related, in particular, the maximum current output.
开关量输出模块的技术指标，它与不同的负载类型密切相关，特别是输出的最大电流。
Output switch module is a low voltage PLC internal drive external signals into the switching signal output device and to achieve internal and external PLC electrical signal isolation.
开关量输出模块是将PLC内部低电压信号转换成驱动外部输出设备的开关信号，并实现PLC内外信号的电气隔离。
Switch your console output to the test server process.
将控制台输出切换到测试服务器进程。
This should mean that the user doesn't have to see the mess of FFMPEG output unless they switch tabs.
这应该意味着，除非用户切换选项卡，否则不会看到乱七八糟的FFMPEG输出。
So in this job, the projection needs to be done in the Output tab of the switch step.
因此在该作业中，映射需要在转换步骤的Output选项卡中完成。
You can switch the console view between different processes, showing output for both the application client, as well as the server process.
您可以在不同的进程之间切换控制台视图，显示应用程序客户机的输出和服务器进程。
Once all three tests that you defined have been executed, switch back to the server process in the process TAB, and take a look at the console output.
一旦您定义的三个测试都被执行后，请在进程(process)选项卡中切换回服务器进程，然后看看控制台输出是什么。
Note: to see the request that cURL makes, add the -v switch (for verbose output), which makes the request but also returns any HTTP request that cURL makes to fetch the result.
注意：若要看到cURL发出的请求，可以添加- v开关(详细输出)，这样不仅会发出请求，而且会返回cURL发出的用于获取结果的任何HTTP请求。
By adding the -f switch, tail will continue to show new output as it occurs.
使用-f开关，当日志增加新的内容时，tail将继续显示新的输出。
The model I have tested with PPC Linux is the older, translucent-and-silver version with a switch between the input and output jacks.
我在PPCLinux上测试的模块比较老，它是一个半透明的银色版本，输入输出之间有一个开关。
That makes Mohanty's silicon bar a kind of nanomechanical switch in which the two voltages are inputs representing a 0 and a 1, and the output depends on whether the input is rising or falling.
这就似的Mohanty的硅条成为了一种纳米机械开关，两个输入的电压代表了0和1，输出取决于输入时在上升还是下降。
The console will switch to the JUnit TestRunner process and the server console output will not be visible.
控制台将切换到JUnitTestRunner进程，而服务器控制台输出将是不可见的。
Switch to the JSP Source tab and verify the code (also see the screen output in Figure 37)
切换到JSPSource页签，并验证代码（也可以参见图 37中的屏幕输出
Switch to the output branches TAB and choose the Yes output branch.
切换到Outputbranches选项卡，并选择Yes输出分支。
Switch to the output branches TAB of the Fork attribute, as Figure 42 shows, to see the output branch of the Fork.
切换到Fork属性的Outputbranches选项卡(如图42所示)，查看Fork的输出分支。
If you switch to the console, you'll see that the program runs and exits without any errors, but it doesn't produce any output.
如果切换到此控制台，您将看到此程序正常运行和退出，但它不会产生任何输出。
Most switch mainframes can be triggered externally via the trigger input and can send an output trigger pulse when the relay contacts have settled.
大多数开关主机都可通过触发输入进行外部触发，并且在继电器触点稳定之后可输出一个触发脉冲。
It can switch a balanced stereo output.
它可以切换一个平衡的立体声输出。
The switch frequency is increased and the output harmonic is decreased while the overcurrent protection is ensured.
保证过电流保护的同时，还提高了开关频率，减小了输出谐波。
A new type of DC switch power which is possessed a DC voltage input and three DC voltage output, and is able to reach higher efficiency has been introduced in this paper.
本文介绍一种新型的直流开关电源，该电源是一种直流电压输入，三种直流电压输出，并能够达到相当高的效率。
To measure the offset of a switch card, connect the output of the card to a pico ammeter or electrometer.
若要测量开关卡的偏移电流，请将卡的输出连接到一台皮安计或静电计。
Switch to the output branches TAB of the join attribute, as Figure 44 shows, to see the output branch of the join.
切换到Join属性的Outputbranches选项卡(如图44所示)，查看Join的输入分支。
Switch to Alpha Output and save a JPEG.
转换到Alpha输出，并保存为一个JPEG文件。
Most switch CARDS have jumpers that can be removed to disconnect the card output from the backplane.
大多数开关卡都有跳线，可以通过拆下跳线将插卡的输出从背板断开。
Switch to the "Output" page, and click on the columns TAB.
切换到“Output”页面，单击columns选项卡。
Switch point. Connect to input or output of integrated chip.
开关点与集成芯片的输入或输出端连接。
Connect an electrometer to the switch card output and measure the cur rent.
将一个静电计连接到开关卡输出并测量电流。
Connect an electrometer to the switch card output and measure the cur rent.
将一个静电计连接到开关卡输出并测量电流。
应用推荐