The reference operating point is introduced.
此外引入“参考工作点”这一新概念。
A new method to determine optimal secure operating point of power system.
一种确定电力系统最优安全运行点的新方法。
The pump operating point is abnormal to normal operating point, that extra point.
此工况点正常也是水泵畸形作业点,即额外点。
In this paper, the selection of the operating point has been discussed in detail.
本文详细地讨论了工作点的选取。
The surge margin at design operating point was estimated by the numerical results.
根据设计转速下的计算结果,预估了压气机设计点的喘振裕度。
The actual operating point of pump is checked out by means of hydraulic calculation.
通过水力计算,校核了离心泵的实际工作点。
As the operating point crosses over the stability boundary, the chug amplitude disappears.
当工作点越过稳定性边界时,低频不稳定的振幅逐渐消失。
The best operating point can be defined as the one that minimizes or maximizes the utility function.
最好的工作点可以被定义为一个最小化或最大化的效用函数。
Then calculate the total number of sound 70% range, the range is useful operating point handbrake handle.
然后算出响声总数的70%方位,这个方位即是手刹手柄的有用作业点。
The initial operating point of sensor should be maintained at the quadrature point for the maximum sensitivity.
最初经营的角度传感器应维持在正交点的最高灵敏度。
It depends on the tube type, the power supply voltage, the reflected impedance, and the required operating point.
这取决于管式,供电电压,反映阻抗,以及所需要的工作点。
This article describe the producing method, the main operating point and the quality standard of the tea seed milk drink.
介绍了茶籽乳饮料的制造工艺、操作要点和质量标准。
When the deformity is not enabled operating point of the Area, the pump will be operating in the inferior race conditions.
当启用不是在于畸形作业点的片区时,水泵将作业在以次工况。
In experiment, steady operating point of combustion can be obtained mainly by setting primary air factor and the size of spout.
在实验中,主要通过调整一次空气系数和引射器喷口的大小,达到稳定燃烧的运行工况。
Basically, we need to use up to a maximum voltage or up to a maximum current but the operating point will never require both at once.
基本上,我们需要使用达到最大电压或最大电流,但是该运行点永远也不需要立刻达到这两个。
From the initial operating point, this method searched the new instability modes with the change of parameters by the way of iteration.
该方法从初始运行点出发,通过迭代确定系统失稳模式随参数变化的情况。
The operating point of the maglev train is concerned with its load, and so the design of the maglev controller has to meet this requirement.
磁浮列车的悬浮静态工作点与承载重量有关,因此对悬浮控制器的设计提出了更高的要求。
Thus the approximate quadratic expression of SVSR boundary can be obtained by the calculation on a given operating point close to the boundary.
由此,通过在一个临近SVSR边界的系统运行点处的运算,可以直接得到SVSR边界的近似二次解析表达式。
Since the response of a HVDC plant dynamically changes with variations in the operating point, a PI controller performance is far from optimum.
由于HVDC系统的响应随运行状态的变化而改变,使得电压互感器控制器的性能很难实现最优。
Thepetrol engine is optimally sized to provide the cruise power at its most efficient operating point, resulting in an improved fuel efficiency overall.
航空煤油发动机的尺寸经过优化设计,已经能够在发动机的最有效的操作点上提供巡航动力,进而从总体上提高燃料效率。
In the second phase, the best operating point, as defined by the decision maker, will be chosen from among the available points on the tradeoff boundary.
在第二阶段,由决策者界定的最佳工作点将从折衷过界的有效点中选择。
Analyze the feedback laser grid-driving power to our feedback channel influence, the laser best operating point and the laser grid-driving power assignment.
分析回传激光器的激励功率对回传通道的影响、激光器的最佳工作点及激光器的激励功率的分配。
Motor system is non linear, however it can be linear approximated in an operating point. First order and second order motor model is used in the discussion.
在实际情况中电机是一个非线性的系统,但是在某一工作区间内完全可以进行线性化,本文采用一阶和二阶电机模型进行讨论。
The fixed-bias amplifier maintains the bias at a more constant level, so it doesn't have the constantly changing operating point that varies with the output level.
固定偏置放大器偏置保持在一个更稳定的水平,因此它不具有不断变化的经营点,随产量水平。
Effect of impeller of different blade profile on the highest pressure point, optimum operating point, shape of pressure curve and efficiency of the fan were analyzed.
分析了不同叶片型线叶轮对风机的最高压力点、最佳工况点、压力曲线形状及效率的影响,同时探讨了风机不同叶片型线的工程实用价值。
A special tool was used for modeling the rotating parts in order to get the components characteristics and draw the maps which can show the current operating point/line.
在旋转部件建模过程中使用工具获取特性数据,并绘制可以即时显示当前工作点/线的部件特性图;
A special tool was used for modeling the rotating parts in order to get the components characteristics and draw the maps which can show the current operating point/line.
在旋转部件建模过程中使用工具获取特性数据,并绘制可以即时显示当前工作点/线的部件特性图;
应用推荐