The System may adjust the control schemes by real time traffic data, which are off-line provided by the fuzzy traffic Decision table based on Rough Sets.
文章前面部分仿真分析通过的各种交通流情况下的基于粗集理论的模糊控制方案表在系统中离线给出，以根据实时的交通流数据查表调用。
The paper mainly focus on the experimental research on pneumatic on-off valve motor position servo control system with PCM control method and self-adjusting PID algorithm.
文章主要研究的内容为利用PCM控制技术，采用自适应PID控制算法，对开关阀式气动马达位置伺服系统进行实验研究。
In this paper, the application of neural network is presented in the control system fault diagnosis. The method of on-line and off-line fault diagnosis are given.
本文介绍了神经元网络在控制系统故障诊断中的应用，讨论了神经元网络用于控制系统故障的离线诊断与在线诊断。
This paper develops the control system of electronically controlled throttle with high speed on off valve.
研究了一种利用高速开关阀对节气门进行电子控制的系统方案。
For primary server may become the bottle of the whole system, VCSR USES a concurrency control protocol based on voting, which also trade-off the network overhead.
针对主服务器可能成为系统中瓶颈的问题，VCSR机制采用基于投票的分布式并发控制协议，同时也均衡了网络负载。
The structure of electrical control system for developing on-off fly - cutter and fly-saw has been studied in this paper considering ensuring cutting length error of fly-cutter and fly-saw.
本文从保证飞剪飞锯切长误差的角度出发，研究了我国尚处在研制阶段的起停式飞剪飞锯电气控制系统的结构组成。
A new slide mode controller is designed for AC servo system. The feed forward signal is used as average control, and fuzzy inference is used to regulate the magnitude of on-off control.
针对交流伺服系统的位置控制，设计出一种新型滑模控制器，以前馈信号作为平均控制，采用模糊推理来调节开关控制的幅度。
Based on the development situations of the pneumatic servo control technique, the main research was also aimed at the PWM and PCM on-off servo control system.
阐述了常规气动伺服控制系统研究的现状，认为以PWM和PCM调制方式为主的开关伺服控制技术仍然是研究的热点。
Presents the design principle and the implement of a pressure control system of numerical control fixture based on high-speed on-off valve.
介绍一种基于高速开关电磁阀的数控夹具压力控制系统的设计原理和实现方法。
An advanced and practical navigation management and control system of night flight aircraft's taking off and on in airport was discussed, and the use of 8098 single chip microcomputer was expounded.
本文论述了一种先进实用的机场夜航机起降导航的控制与管理系统，并阐述了8098单片微机的应用。
The traditional control cabinet of oil-pumping unit is using continuous electricity contact system through the mechanical touching point by closing and opening to achieve the circuit's "on" and"off".
传统的抽油机控制柜大都采用继电接触系统，通过机械式触点闭合、断开实现电路导通或断开。
The motor is linked up to a programmable-logic control system, and can be switched on and off automatically in the relevant phases of the mashing process.
电机与一台可编程序控制器连接，可以在糖化过程的每个阶段自动打开或关闭，而且还可发出不同频率。
The Research on the Electro-hydraulic Control System with High-speed ON/OFF Valve;
研究了一种利用高速开关阀对节气门进行电子控制的系统方案。
The system functions of ignition on-off control, multi-way power supply on-off control, interface parameters measurement, system self-check, system calibration, replay analysis are realized.
完成了火炮的点火通断控制、多路工作电源输出通断控制、接口参数测试、系统自检、系统校准，回放分析等功能。
Using the application on baking paint stove, it appears that smith prediction on-off controller can reduce the oscillation value of on-off control system and improve the accuracy effectively.
通过在烤漆生产线上的电阻炉的实验应用，显示史密斯预估位式调节器能有效抑制纯滞后造成的非线性位式控制系统的持续振荡，有效提高位式温度控制系统的控制精度。
This paper analyzes the tension control strategies of rewinder and the principles of the T400 technology board, designed a system of reeling-off direct tension control based on T400.
本文分析了复卷机退纸辊张力控制方式及T400工艺板的工作原理，设计了一套基于T400工艺板的退纸辊直接张力控制系统，详细说明了系统的软硬件组态。
The conventional sequence system of the power plant is only to control the single equipment and the supporting facility or among the on-off signals of several equipment.
传统电厂的顺控系统只是控制单台设备及其辅助设备的启停或是几个设备之间开关量的控制。
X10 is essentially a remote control system for your home, limited to on, off and dim commands.
X10基本上是家用的遥控系统，局限于开、关和明暗调节的命令。
Discontinuous variables such as shown in Fig. 2-1A-2c occur in "on-off" or "bang-bang" control system and are treated separately in a subsequent paper.
如图2-1A-2c所示的不连续变量，主要是在“通-断”控制或者“砰-砰”控制出现，将后续章节单独处理。
System control arithmetic adopts variable-structure-control, which can choose on-off-control and fuzzy-control and integral-control strategy automatically.
控制算法采用变结构控制器，可根据系统误差及其变化率的大小自适应选择通断控制、模糊控制、积分控制等控制策略。
Causes to keep off the numerical control system to store the reduction lowly the complex components procedure to carry on processes fast into possibly.
使得中低挡数控系统存入缩短的复杂零件程序进行快速加工成为可能。
Causes to keep off the numerical control system to store the reduction lowly the complex components procedure to carry on processes fast into possibly.
使得中低挡数控系统存入缩短的复杂零件程序进行快速加工成为可能。
应用推荐