Then their centers have been offset by 25 meters along the X axis.
那么他们的中心是沿着X轴偏移了25米。
To solve the optic axis offset of the TV camera, this article proposed a dynamic software compensation technology in continual focal variation process.
为解决电视摄像机在连续变焦过程产生光轴线的偏移问题，提出了一种动态软件补偿技术。
The paper analyses the effect of translation and offset angle of the cone axis to shaft one on the gap variation between two ring-button, which position on two cones.
分析了牙轮钻头安装和磨损间隙引起牙轮相对牙爪轴线的平移和倾斜对相邻锥体上球齿间隙的影响，通过计算，当牙轮、牙爪轴线轴向、径向平移使球齿的趋近量有抵消的趋势；
In a side view, the axis (c) of the crankshaft (28) is offset upward from the center line (a) of the cylinder.
当从侧向看时，曲轴(28)的轴线(C)从气缸的中心线(A)向上偏移。
The space tool radius offset G instructions with the developed approach will avoid NC codes regeneration due to tool wear or tool change during the three-axis NC flank milling process.
基于该算法的空间刀具半径补偿G指令将可避免由于刀具磨损和刀具更换导致的三轴侧铣数控代码重生成。
The shaft is structured to optionally move in the offset cam, and the display panel unit is structured to rotating around a spin axis when the shaft moves in the offset cam.
该轴构造成在偏心凸轮内选择性地移动，并且显示面板单元构造成当轴 在偏心凸轮内移动时绕旋转轴线旋转。
The points (350) are offset (r) with respect to the rotation axis (65) of the rotor (100).
点(350)相对转子(100)的旋转轴(65)被偏置。
Through the analysis of the rotation of the wheel center round the kingpin axis, derive spindle offset and longitudinal kingpin offset algorithm;
通过分析车轮转动时轮心相对于主销轴线的运动，推导出主销横向偏移距及主销纵向偏移距的算法；
When the distance of two nozzles was fixed, the offset of impinging stagnation point on the axis increased with the ratio of velocity and the nozzle diameter.
当喷嘴间距一定时，轴线撞击面驻点偏移量随气速比和喷嘴直径的增大而增大。
On this basis, a further discussion about whether the offset of box axis can impact the meshing pair is made.
在此基础上，进一步讨论了箱体轴线的偏移对齿轮啮合的影响。
Earth's figure axis is not the same as its north-south axis; they are offset by about 10 meters (about 33 feet).
地球的数字轴是不一样的南北轴线，它们是约10米(约33英尺)所抵消。
The hollow-axis motor drives the offset nozzle and rotates the arc on the tip of wire at high speed, so as to ensure enough penetration into the sidewalls in narrow gap welding.
在该系统中，焊丝穿过电机的空心轴后从导电嘴的偏心孔送出，电机带动导电杆和偏心导电嘴旋转，从而使焊丝端部的电弧以一定直径高速旋转，以保证窄间隙焊接接头具有足够的侧壁熔深。
The sight telescope was mounted in such a way that the line of sight could be offset from the axis of the bore of the gun to correct for range, drift, and relative motion of gun and target.
这种瞄准镜底座是可以转动的，使得瞄准线能够偏离炮膛轴线以修正射程，偏流及火炮与目标之间的相对运动。
An offset can be added to the Y-axis.
可以添加一个偏移的Y轴。
An offset can be added to the Y-axis.
可以添加一个偏移的Y轴。
应用推荐