Therefore, the offset voltage should be measured periodically for the most effective offset correction.
因此，为了获得最有效的偏移修正效果，应该定期测量偏移电压。
The contact potential or thermoelectric offset voltage is the key specification of a switch card designed for low voltage switching.
接触电势或热电效应偏移电压是设计用于低压切换的开关卡的关键技术指标。
This offset voltage will be added to the voltage measurement.
该偏移电压将被叠加到电压测量值中。
Switching and measuring voltage sources with high internal impedance are subject to a number of errors, including offset currents, stray leakage paths, and electrostatic interference.
切换和测量具有高内阻的电压源会受各种误差的影响，包括偏移电流、寄生漏泄通路，以及静电干扰。
The relative polarities of the two voltages will determine whether the offset voltage adds to or subtracts from the source voltage.
这两个电压的相对极性决定了偏置电压是加到源电压上去还是从源电压中减去。
Other CARDS, such as the Model 7700 20-channel Differential Multiplexer Module, use latching relays, and the offset voltage is the same whether the poles are used as a single pole or as a pair.
其它开关卡，例如7700型20通道差分复用模块，采用的是闭锁型继电器，无论是成对还是单独使用一个闸刀，偏移电压都是相同的。
Any offset current flowing through a high impedance device will cause an unwanted voltage to appear across the device.
通过高阻装置的任何偏移电流都会导致装置两端出现不希望的电压。
The zero reading may also vary as the ambient temperature changes. This effect is usually referred to as the temperature coefficient of the voltage offset.
仪器的零点读数也会随着环境温度的变化而变化。这种效应通常称为电压偏置温度系数。
The offset voltage adds directly to the signal voltage and can be modeled as an unwanted voltage source in series with the intended signal.
偏移电压被直接叠加到信号电压之上，可以被模型化为一个未知的电压源，与已知信号相串联。
However, a number of error sources in the circuit may be seen as a non-zero voltage offset.
然而，电路中的若干误差源可以引起非零的电压偏置量。
The offset voltage will cause an error in the applied stimulus to a device under test or the value measured by the voltmeter.
偏移电压会导致施加到被测装置的激励发生误差，或者使伏特计的测量值发生误差。
AC current or voltage source. DC offset can be specified.
交流电流源或电压源。可指定直流偏移。
After a step change in the ambient temperature, the voltage offset may change by a relatively large amount, possibly exceeding the published specifications.
在环境温度发生一个跳变之后，电压偏置的变化可能会比较大。其变化量可能会超过公布的仪器技术指标。
While one junction will adjust to the new ambient temperature quickly, another changes slowly, resulting in a temporary change in voltage offset.
一个结点已经迅速地调整到新的环境温度，而另一个结点则变化较慢，这样就产生了瞬时的电压偏置变化。
The thermoelectric offset voltage due to the switch card and the interconnecting cable may be compensated for by using a short-circuited channel to establish a zero reference.
由于开关卡和互连电缆引起的热电效应偏移电压可采用一个短路通道来建立一个零参考，从而进行补偿。
This error voltage is known as contact potential or offset voltage.
该误差电压就是所谓的接触电势或偏移电压。
This paper presents a new compensation method for stator voltage amplitude and DC offset, which can improve the performance of the speed sensor-less vector control of induction motor.
为了提高异步电机无速度传感器矢量控制的低速性能，提出了一种定子电压幅值和直流偏置补偿办法。
The waveform is generated by MAX038. It is very convenient to adjust the frequency, duty cycle and offset voltage of the waveform by changing parameters of the corresponding pins of the chip.
使用MAX038波形发生芯片产生波形，通过修改MAX038相应引脚的参数方便地实现输出波形的频率和占空比及偏置电压参数的调节。
Slope and offset pots R5 and R2, together with the adjacent resistors, from a voltage scaling network providing the reference voltage at TP2.
调整斜率和偏移的电阻R5和R2及其邻近电阻共同组成一个电压测量网络来提供TP2上的参考电压。
The resulting offset voltage is subsequently subtracted from the measured signal to maximize measurement accuracy.
随后从被测的信号中减去测量出的偏置电压，以便最大限度地提高测量的准确度。
A deep negative feedback operation amplifier used in band gap reference is a common source and gate folded cascade operation amplifier with a lower offset voltage and a higher gain.
该带隙电压基准源电路中的深度负反馈运算放大器为低失调、高增益的折叠型共源共栅运算放大器。
The simulation results show that the amplifier of improved control circuit not only solve the question of output DC offset, but also keep the voltage gain lowered by voltage compensation technique.
仿真结果表明，改进控制电路后的系统不但解决了输出直流偏置问题，而且解决了电压补偿方法所造成的放大器增益下降问题。
Due to its relative low amplitude properties, the bioelectricity signal is easy influenced by surrounding factor, the amplifier with low noise and voltage offset is required.
由于生物电信号非常微弱，容易受量测环境及电路本身等因素所影响，故要求该放大器具有低噪声和低失调电压的性能。
One disadvantage of this method of stabilization is the additional output noise and offset voltage caused by increased amplification of input-referred voltage noise and input offset voltage.
这种稳定方法的一个不足是：输入端的有关电压噪声和失调电压增大会额外地增加输出噪声和失调电压。
Then, switch S1 to the "measure" position and adjust RT2 to null any voltage offset referred to the output voltage.
然后，转换S1到“测量”位置，并调整RT2到涉及输出电压的所有无效的电压偏置。
In layout design, the cross-couple structure is adopted in the input stage to minimize the MOSFET mismatch due to process, and consequently to lower the offset voltage in the circuits.
在版图的设计上，对输入级采用交叉耦合结构，减小由于工艺原理引起的MOS管匹配，从而减小电路的失调电压；
Based on analyzing the status of hall and offset voltage, a completely new and comparatively simple hall signal regeneration circuit was brought forward.
以霍尔电压及失调电压的状态为出发点，提出了一种更简单的霍尔信号再生电路设计方案。
The technique transfers the offset voltage from the output to other parts of the differential amplifier and can greatly reduce the input-referred offset voltage without extra power consumption.
这种技术在不需要增加功耗的基础上，通过把输出端的失调电压转移到差分放大器的其他节点，从而达到减小输入参考的失调电压的目的。
The technique transfers the offset voltage from the output to other parts of the differential amplifier and can greatly reduce the input-referred offset voltage without extra power consumption.
这种技术在不需要增加功耗的基础上，通过把输出端的失调电压转移到差分放大器的其他节点，从而达到减小输入参考的失调电压的目的。
应用推荐