It's important to put a lock washer on that last nut, or it can work loose.
重要的是要在最后一个螺母上安装一个防松垫圈，否则它会逐渐变松。
Remove a shaft nut and washer.
取下主轴螺帽和垫圈。
Each piston disassembled and polished, each nut and washer cleaned or replaced, accounted for.
每个活塞都要拆下来并且打磨，每个螺母和垫圈都要清洗或更换，并且一个都不能少。
Install the sealing washer, flat washer and nut as described in the Floor.
如同在底板固定一节里所记述的那样，安装密封垫圈，平面垫圈及螺。
NOTE: If minor leakage occurs, remove lock screw, lock washer and cap and lightly tighten packing gland nut.
注：如果出现少量的泄漏，则拆卸锁紧螺丝，然后锁住垫圈和阀盖，然后轻轻紧固填料压紧螺母。
The spindle nut must be tightened using a paper washer.
必须用纸垫圈使心轴螺帽紧固。
They are made up of sleeve, lock nut and lock washer.
它由称套、锁紧螺母、锁紧垫圈组成。
Hold stem (27) on wrench flats and remove nut (51), lock washer (46), diaphragm plate (60) and diaphragm.
在扳手的平面上握住阀杆(27)并拆卸螺母(51)，锁紧垫圈(46)，隔膜板(60)和隔膜。
Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem.
松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。
Washer should be placed on one side of nut.
垫圈放置在螺母一侧，不得装反。
Smaller sizes use a lock nut with a locking washer, larger sizes use a nut with locking clip.
小尺寸轴承使用带锁紧垫圈的锁紧螺母大尺寸的轴承使用带锁紧卡箍的锁紧螺母。
Now my main production plant in fasteners products nut, plain washer series products.
现在我厂主要生产紧固件产品中的螺母、平垫圈类系列的产品。
Right dropout - right chain tensioner - right torque washer - right cap nut.
正确的辍学-链拉紧的权利-权利扭矩洗衣机-帽螺母的权利。
The minimum across flats dimension of the hex bolt or hex nut being used to test the loose washer must not be greater than 1.5 times the basic thread size.
用于试验非组合用垫圈的六角螺栓或六角螺母的最小对边宽度不能大于垫圈内径所对应的螺纹公径直径的1.5倍。
Our company Specially offer Threaded Rod and Flat Washer, also together with Nut.
我们公司主要生产牙条，垫圈，还有螺母。
In order to prevent the inverse loosing after the operation, the spring washer (5) is added between the nut and the washer.
为了防止术后反松，在螺帽与垫圈间又增加了一弹簧垫圈(5)。
The engagement section having a T-shaped cross-section may have an L-shaped member, a washer, an intermediate member, a threaded bolt and a nut.
订婚后的第一个T形截面可能有一个L形的成员，洗衣机，中间成员，螺纹螺栓和螺母。
The pressurization is conducted by a screw, a nut and a washer.
利用螺丝、螺帽及垫圈进行加压；
On the rod body, a washer is sheathed with the part which is corresponding to the part between the tray and the screw nut of each compressing piece.
杆体上对应于每套压紧件中的托盘和螺母之间处均套装一个垫圈。
The swinging rotating joint consists of spherical body, thread joint sleeve, locking screw nut, large copper washer and two spherical rings.
本发明摆动旋转接头由球型接头体，螺纹接头套，锁紧螺帽，大铜垫和两个球面转环构成。
The swinging rotating joint consists of spherical body, thread joint sleeve, locking screw nut, large copper washer and two spherical rings.
本发明摆动旋转接头由球型接头体，螺纹接头套，锁紧螺帽，大铜垫和两个球面转环构成。
应用推荐