The theoretical analysis and numerical experiments with commercial software about sampling process in electrophoresis chip were presented.
对毛细管电泳芯片的压力进样过程进行了理论分析，并用商用软件对这一过程进行数值实验。
The stability of coal pillar of the short-wall mining was analyzed systemically by numerical simulation with the rock failure process analysis software (RFPA2D).
采用岩石破裂过程分析软件RFPA2D系统，对短壁机械化开采的煤柱稳定性进行数值计算与分析。
The numerical analysis was performed on temperature distribution of the outlet nozzles in main vessel of SCWR(supercritical water reactor) by using computational fluid dynamics software CFX.
采用计算流体力学软件CFX对超临界水冷堆主容器出口管的温度分布进行数值分析。
We had made numerical and modal analysis on the dynamic feature of F320 model derrick with ANSYS software and modal analysis technique.
使用ANSYS有限元软件、实验模态分析技术对F320型石油井架模型的动态特性进行了数值与试验分析。
Numerical simulation analysis is made of the paste piping transportation using FLOTRAN CFD calculation hydrodynamic analysis module in ANSYS software based on the paste filling mechanical parameters.
以膏体充填力学参数为基础，运用ANSYS软件中的FLOTRANCFD计算流体动力学分析模块对膏体管道输送进行了数值模拟分析。
Numerical analysis is applied with FEM software on the typical joint experiment of one building project.
结合某实际工程节点的模型试验，应用有限元软件对其进行数值分析。
The numerical simulation of drawing process for front extension to side panel is studied by using the three-dimensional sheet metal forming analysis software PAM-STAMP.
采用板料三维成形分析软件PAM - ST AMP对某车型侧围前延长件的拉深成形过程进行了数值模拟仿真。
To discover the mechanism of progressive failure of rock slope, physical simulation experiment and numerical simulation analysis by means of FLAC software have been done simultaneously.
为了揭示岩体边坡渐进破坏的机理，在对边坡渐进破坏进行物理模拟的同时，应用FLAC软件对边坡渐进破坏过程进行了数值模拟。
Numerical analysis of static piling based on the commonly used software ANSYS is done.
在通用软件ANSYS平台上对静力压桩进行数值分析。
At the same time, it could get an assessment about biofidelity and reliability of the results analysis for HSRC columns of numerical simulation with the software (ABAQUS).
同时可得，将软件ABAQUS用于型钢高强混凝土柱数值模拟分析时，其计算结果具有一定的精确度与可靠性。
This paper developed a practical system software of microcomputer numerical control system based on the analysis of the hardware construction and principle of the AC servo X - Y table.
本文针对微机数控交流伺服X-Y工作台的硬件结构以及其工作机理，介绍了一套可实际应用的微机数控交流伺服系统软件的开发。
Using numerical simulation software, the paper analysis the influence of secondary air to the pollutant discharged in high temperature and low oxygen air combustion.
利用数值模拟软件分析了二次空气对高温低氧空气燃烧污染物排放的影响。
Using fluid dynamics analysis software CFD made a numerical simulation to the BOP control system pressure relief valve under the valve different working conditions;
使用流体力学分析软件对减压溢流阀在阀口不同开度条件下进行了阀内流场的数值模拟和仿真；
The numerical simulation and analysis of shear resistance behavior of two-side connected steel-plate shear wall (SPSW) was carried out by the finite element software ANSYS.
采用ANSYS有限元程序对两边连接钢板剪力墙进行数值模拟分析。
The numerical simulation of the new type of DNG is studied by using FDTD method and CST software, and the physical mechanism analysis for this structure is discussed in detail.
用时域有限差分法和CST软件对该新型结构进行了模拟对比，并对其物理机理进行了分析，解释了其双负效应发生的原因。
The finite element analysis software, which was based on the general finite element software package, was developed for numerical simulation of the entire composite cure process.
以通用有限元软件包为基础，开发了能够模拟复合材料整个制造过程中复杂物理化学变化的软件。
Numerical analysis of the kerosene spray supersonic combustion was carried out in the dual-mode supersonic combustor with the CFD software.
利用计算流体力学软件对煤油在所设计的双模态超声速燃烧室内的超声速喷雾燃烧进行了数值模拟。
We can conclude from experiments and numerical comparisons that this software package can provide timesaving and accurate thermal analysis for electronic equipment.
经过实验研究及数值分析对比可知：该软件可以对计算机机箱类的电子设备进行相对精确同时又比较省时的热特性分析。
The numerical modeling and analysis of static and dynamic strength and characteristics of the low floor city bus body structure are carried out in the paper, using a standard CAE software.
利用标准的CAE软件平台，对低地板城市客车车身结构进行数值建模和静动态特性分析。
Compared with the numerical simulating calculation, the result of software analysis has the basic same deformation time point but a different deformation length of 2.62%;
软件分析结果与数值模拟计算对比，变形时刻基本相同，变形长度相差2.62%；
According to the latest test results abroad, the software ANSYS8.0 is applied to carry out the finite element nonlinear analysis. The most numerical calculating results agree well with the test data.
本文利用大型通用有限元软件ANSYS8.0进行了数值模拟，有限元计算结果与国外最新试验数据吻合良好。
According to the latest test results abroad, the software ANSYS8.0 is applied to carry out the finite element nonlinear analysis. The most numerical calculating results agree well with the test data.
本文利用大型通用有限元软件ANSYS8.0进行了数值模拟，有限元计算结果与国外最新试验数据吻合良好。
应用推荐