IP address to assign to the network adapter.
要分配给网络适配器的IP地址。
A host name is associated with a network adapter.
主机名与一个网络适配器相关联。
The first network adapter is connected to VM Network.
第一个网络适配器连接到VM 网络。
Total data rates for each network adapter by time of day.
每个网络适配器的每日各时段总数据速率。
Only hdisk0 and the first network adapter (ent0) were in the list.
列表中只有hdisk0和第一个网络适配器(ent0)。
Here you can change the network adapter, disk mode options, and more.
在这里,可以更改网络适配器、盘模式(disk mode)选项,以及更多其他的属性。
The most important component you will be working with is your network adapter.
您将使用的最重要的组件是网络适配器。
Lan Monitor: Displays information about every network adapter on your computer.
LanMonitor:显示计算机上每块网卡的信息。
Your host has an active network adapter that can be used to send out the request.
您的主机有一个活跃的网络适配器,可以使用它发送请求。
To configure a network adapter on a server running AIX, perform the following steps.
要在运行AIX的服务器上配置网络适配器,请执行下列步骤。
Each network adapter should be configured with a boot address and associated host name.
每个网络适配器应该配置一个引导地址和相关联的主机名。
Before beginning to configure the network adapter, first document the following information.
在开始配置网络适配器之前,首先记录下列信息。
This will prevent an IP address being configured on the physical network adapter used for the install.
这会防止在安装所用的物理网络适配器上配置IP地址。
Select the network adapter you want to configure from the list shown in figure 1, and then click Enter.
从图1显示的列表中选择要配置的网络适配器,然后按enter。
The target host is running and has an active network adapter configured with the IP address that you used.
目标主机正在运行,而且在您使用的IP地址上配置了活跃的网络适配器。
It USES the physical network adapter using the SEA just created to access the public network (see Listing 3).
它使用刚才创建的SEA,通过物理网络适配器来访问公共网络(请参见清单3)。
To improve transfer and receive large amounts of data, you can configure a couple of network adapter Settings.
要改进数据的传输和接收,可以配置一些网络适配器设置。
As mentioned earlier, when setting up the network adapter, you typed the IP address location to a name server.
如前所述,在设置网络适配器时,您输入了名称服务器的IP地址。
One network adapter for the control node will suffice in low-traffic Settings, but two is better on busy networks.
控制节点使用一个网络适配器便足以满足低流量设置,但是对于繁忙的网络来说,有两个网络适配器更好。
Simply configure your network adapter, direct DNS to a valid DNS server, and you'll be surfing the Web in no time!
只需配置您的网络适配器,将DNS 指向有效的 DNS服务器,您立即就可以在网上冲浪!
Now that you've configured the network adapter and modified /etc/resolv.conf to your liking, you can test your Internet connection.
现在已经配置了网络适配器并根据您的喜好修改了 /etc/resolv.conf,接下来可以测试您的Internet连接。
To run this wizard at least one network adapter must be enabled. Enable an adapter in network Connections and then rerun the wizard.
必须至少启用一块网络适配器才能运行此向导。请在网络连接中启用适配器,然后重新运行此向导。
After you select the desired network adapter, a new window is built that displays all the Settings you need to configure the network adapter.
选择所需的网络适配器后,将生成新的窗口,其中显示配置网络适配器所需的全部设置。
One of the easiest ways to verify that you've configured your network adapter correctly and can communicate with the Internet is to ping an IP address.
验证您已正确地配置了网络适配器并可以与Internet通信的最简单的方法之一是ping某个IP地址。
It not only manages the connectivity of the local network adapter, but also provides a mechanism to manage the connectivity of registered remote resources.
它不仅管理本地网络适配器的连接性,而且还提供了管理已注册的远端资源连接性的机制。
To construct a screensaver, the best way is to configure it with a virtual CD-ROM drive, keyboard, screen, and mouse, but without any virtual disks or network adapter.
要构造一个屏幕保护程序,最好的方式就是为其配置一个虚拟的光驱、键盘、屏幕和鼠标,但是不需要虚拟磁盘和网络适配器。
When an operating system is interrupted because of a hardware event (such as the presence of a packet through a network adapter), the processing begins in an interrupt.
操作系统会因为一个硬件事件而产生中断(例如出现了一个来自网卡的数据包),对该事件的处理过程从一个中断开始。
If it isn't, there may be a problem with the physical connection from the network adapter on your host to the gateway (for example, a faulty switch port, cable, network card).
如果无法到达这个网关,那么从您主机上的网络适配器到网关的物理连接可能有问题(例如交换机端口、线路和网卡有故障)。
Note that the Argus and process_racluster.pl program (listed below) need to be run as a user with appropriate privileges for accessing the network adapter in promiscuous mode.
注意,需要以拥有在promiscuous模式下访问网络适配器的相应权限的用户身份运行Argus和 process_racluster.pl程序(下面列出)。
The Lotus Expeditor network component contains a system connectivity monitor that constantly monitors the state of the network adapter and notifies registered components of any state changes.
LotusExpeditor网络组件包含了一个系统连接性监测器,可不断地监测网络适配器的状态并在发生状态更改的时候,通知经过注册的组件。
应用推荐