The dynamic system responses for upwards and downwards impacts with various structural parameters using the commercial software MSC.
针对系统受向上和向下冲击两种情况，以及系统不同的设计参数，采用商用软件MSC。
As to the powder compaction process, finite element software MSC.
对于粉末压制成形过程，利用有限元软件MSC。
By using the large finite element method software MSC.
利用大型有限元分析软件Msc。
With the transient dynamic software of MSC.
本文运用瞬态动力学软件MSC。
Finally, in finite element analysis software MSC.
最后，在有限元分析软件MSC。
For the sake of realizing the war-time MSC, we should use all kinds of computer technology to empolder relative manage system software.
为了使战时军事供应链管理成为现实，必须借助于高科技手段，利用各种计算机技术开发相关的系统管理软件。
The finite element analysis software of MSC.
使用有限元分析软件MSC。
In order to solve the problem of door weather strips which compression load are out of their standard, the nonlinear finite element software, MSC.
为了解决某轿车车门密封条压缩负荷超标的问题，采用非线性有限元软件MSC。
To explore the influence of maximal internal pressure on forming tri-branch tube, the procedure of forming tri-branch tube is simulated by FEM software MSC.
以内高压成形三通管过程中最大内压的影响为研究目标，采用有限元分析软件MSC。
Based on the advanced nonlinear finite element analysis software MSC.
以大型非线性有限元软件MSC。
Finally through finite element software MSC.
最后通过有限元软件MSC。
The separation simulation of different fairing designed of new generation launch vehicle by means of MSC. NASTRAN and MSC. ADAMS software was computed, and compared with the ground test result.
NASTRAN和ADAMS软件仿真模拟了新一代大运载火箭整流罩不同设计方案的地面分离，并与试验结果进行了比较。
With finite element software MSC.
应用大型通用有限元分析软件MSC。
Temperature field in the laser hardening process was numerically simulated by MSC. Marc software. The calculated results are in good agreement with the experimental results.
采用有限元软件对激光强化过程中的温度场进行数值模拟，数值模拟结果与实验结果符合较好。
By the large engineering software MSC.
借助于大型工程软件MSC。
Using finite element analysis software MSC.
并以有限元分析软件MSC。
METHODS: According to industrial design chart of AID, finite element software MSC.
方法：根据人工椎间盘的工业设计图，利用有限元软件MSC。
By using the large finite element software MSC.
利用大型有限元软件MSC。
The article simulates the processes of tube drawing when the mandrel's position is different in the deform zone by using the finite element analysis software of MSC.
利用MSC MARC有限元仿真软件模拟了固定短芯棒拉拔时芯棒在变形区中不同位置时的管材拉拔过程，研究芯棒位置不同对管材内径尺寸精度影响的规律。
Based on a type of motorcycle frame, this paper USES the UG software for entity sculpt combining some parts drawing, and grids in the pre-disposing and post-disposing software MSC.
以某型号的摩托车车架实物为基础，使用三维造型软件UG进行实体造型，在前后处理MSC。
The contact problem between the landing cushion of the hovercraft and the vehicle deck is analysed with the help of FEM software MSC.
然后着重分析了车辆甲板和气垫船着陆垫接触作用的工况，采用非线性功能强大的MSC。
In this article, it introduces the network management technology and the design of Digital Trunking MSC network management Software that base on the SNMP protocol.
本文简要介绍了网络管理技术，提出了一种基于简单网络管理协议的数字集群移动交换中心网络管理软件的设计与构架方案。
The thin strip rolling process of 4-high strip mill is simulated and analyzed by using 3-D elastic-plastic FEM with software MSC.
采用三维弹塑性有限元法对四辊轧机轧制薄带钢的过程进行了模拟。
The thin strip rolling process of 4-high strip mill is simulated and analyzed by using 3-D elastic-plastic FEM with software MSC.
采用三维弹塑性有限元法对四辊轧机轧制薄带钢的过程进行了模拟。
应用推荐