A simple filtering and oil-recovery device for purifying the mould cooling air containing large amount of oil fumes in the exhausting pipelines has been described.
介绍了一个简单的过滤和油回收装置，用于带油烟的模具冷却凤排放时进行净化和油回收。
Through proposed equivalent mould cooling method, the temperature evolution of cold feeding ingot and hot feeding ingot process were simulated and investigated, separately.
采取等效模冷法，分别模拟了冷送和热送过程钢锭表面和心部温度场的演化。
Function description: quicken the cooling of rubber mould; shorten the interval time of using the mould (increase the output); reduce the high-temperature bearing time (lengthen the service life).
功能描述：加快橡胶模具的冷却、减少模具再次使用的间隔时间(提高产量)、减少高温承受时间(使用寿命更长)。
Simulating different solidification cooling rate with step-metal mould and sand mould, the effect of solidification cooling rate on microstructure and properties of high boron steel were studied.
利用阶梯型腔金属模和砂型模拟不同的冷却速度，研究了冷却速度对高硼钢凝固组织和性能的影响。
The paper introduces one to four moulds production of PET bottle blanks using domestic plastic injector. Selections of cooling temperature of mould and injector temperature and pressure are included.
本文介绍了利用国产注塑机配备一出四模具生产PET瓶坯的生产工艺，模具冷却温度及注射温度、压力的选择。
Optional-laying cooling water channel in the mould could be obtained by precision casting, and optimal cooling effect could be achieved.
利用精密铸造的方法可以获得任意布置冷却水道的模具，达到最佳的冷却效果。
It shows that reasonable use of artificial roughness on the cooling surface of the mould can enhance the cooling of the mould and increase productivity.
计算和分析表明：在热成形模具外冷却表面合理地设置人为粗糙度有利于强化对模具的冷却，提高生产效率。
The finite element mould of the cast steel cooling stave of blast furnace was established and the initial conditions and boundary conditions were determined.
建立了高炉铸钢冷却壁的有限元模型，确定了冷却壁温度场模拟的初始条件和边界条件。
Step 5: Cooling. Place the chocolate-filled mould in the refrigerator. This will make the chocolate cool and harden.
第五步：冷却。将盛满巧克力的模具放进冰箱。让巧克力冷却、凝固。
The mould technology with high cooling intensity is adopted in the steel-making plant of Laigang to transform general built-up mould to high effective tube mould.
莱钢炼钢厂应用高冷却强度结晶器技术，将原组合铜板式断面结晶器改造为高效管式结晶器。
The influences of cooling rate of the mould, pouring temperature, nodularity and chemical composition on hardness of roll body were described, and the measures for solve problems were proposed.
对铸型冷却速度、浇注温度、球化率和化学成分对辊身硬度的影响进行了论述，并提出了解决问题的措施。
The adoption of the chamfered mould, slow cooling in CC and increasing the edge and corner temperature could effectively suppressed the edge defect of pipeline steel.
采用倒角结晶器及连铸弱冷工艺、提高轧件边角部温度可以有效抑制管线钢边部缺陷的产生。
The results show that the casting with good quality can be obtained by removing one ingate and adding cooling waterway into mould.
结果表明，采用去掉一个内浇口，增加模具冷却水道的工艺可获得质量较好的铸型。
Because of the higher rate of cooling in the region of the shoe or mould, different stresses and structures of the metal occur in this region than in the remainder of the workpiece.
由于较高的冷却区域的鞋或模具，不同的强调和结构的金属发生在这一地区比其余的工件。
Shaped mould is the important part of extrusion die for injection moulding. The cooling process of shaped plastic in shaped mould was studied using numerical simulation.
定型模是挤出模具的重要组成部分，采用数值模拟方法研究定型模内塑料异型材的冷却过程，可以指导定型模冷却系统的设计。
Critical areas of wide slab caster design will be examined including mould steel flow conditions, mould design, strand guide support design, secondary spray cooling design and caster automation.
宽板坯连铸设计的关键在于结晶器内的注流状况，结晶器、铸坯导向段的支撑和二冷喷淋的设计以及连铸自动化。
The quantitative relation between hot pipe structure and cooling ability of partial die casting mould was approached.
研究热管结构对压铸模具冷却能力影响的定量关系。
The cast ingots prepared using sand mould and metal mould were analyzed to investigate the effect of cooling rates on morphologies and characters of M2C eutectic carbides in M2 high speed steel.
采用砂型和金属型铸造制备m 2高速钢铸锭，研究了冷却速度变化对高速钢m 2c共晶碳化物形态及性质的影响，探讨了M2C共晶碳化物形态变化的机理。
The design of cooling system for plastic injection mould has much to do with the production efficiency and product quality.
注塑模冷却系统的设计直接影响着注塑生产效率及塑件质量。
This paper analyzed the effect of the volume rate of flow, the temperature the speed of flow and the quality of cooling water on the service life of copper pipe mould.
本文分析了连铸结晶器铜管用的冷却水的流量、温度、流速、水质对铜管寿命的影响。
The article states the forming technology of the round cooling tower mould of glass fiber reinforced plastics, mould structure form and manufacturing method.
简述圆形玻璃钢冷却塔模具成型工艺，模具结构形式以及制造方法。
Deposit metal samples are prepared by GMAW shielded with different gases in copper mould with water cooling.
采用不同配比的保护气体，在水冷铜模中堆焊焊缝金属，获得不同扩散氢含量的熔敷焊缝试棒。
The results show that: secondary melting process and cooling in copper mould can achieve homogeneous fine microscopic structure.
结果表明：采用二次熔炼铜模浇铸的铸锭方式可以获得均匀、细小的共晶组织；
It is a key to introduce sensitivity analysis method into injection mould CAE for cooling system automatic and optimum design. It also becomes an important content in cooling system design.
将灵敏度分析方法引入注塑模温度场CAE中，是如何实现冷却系统自动优化设计的核心，也是冷却系统设计的一个重要方向。
A new method of balanced cooling permanent mould was described. The effect of balanced cooling on the piston quality is discussed. The key to improve quality is to reinforce the cooling.
提出了活塞铸造中模具均衡冷却的新方法，讨论了均衡冷却对活塞质量的影响，指出合理加强冷却是获取高质量活塞的关键。
Once a predetermined steel level is attained in the tundish, nozzles are opened and the molten steel feeds the open-ended mould set in a frame with internal water-cooling.
一旦中间包内的钢水达到规定的高度，水口就被打开，钢水注入放在托架上有内部水冷装置的结晶器内。
Cooling system of plastic mould can greatly influence the product quality and production efficiency.
冷却系统对于塑件的质量和生产效率有着重要的影响。
Cooling system of plastic mould can greatly influence the product quality and production efficiency.
冷却系统对于塑件的质量和生产效率有着重要的影响。
应用推荐