In this thesis, how to design a brushless DC motor control chip is discussed in detail.
本论文详细阐述了如何设计一个无刷直流电机的控制芯片。
The design of the single chip system, sample box thermostat circuit, sample position detecting circuit and step motor control circuit are discussed.
着重讨论了单片机系统、样品箱恒温电路、样品位置检测电路和步进电机控制电路的设计。
Compressor cylinder to the scientific design and motor, piston, transmission system of quality control, can greatly improve the gas production unit power.
对压缩机汽缸的科学设计以及电机、活塞环、传动系统质量的控制，能够大幅提高单位功率下的产气量。
One kind of stepping motor control card based on ISA bus of PC which achieved multi-spindle linkage control is introduced, its principle and design of hardware construction and software are discussed.
介绍了一种基于PC机的IS A总线步进电机控制卡，实现多轴联动控制，讨论了其工作原理和硬件结构设计、软件设计。
The design method and driving circuit for microstepping control of step motor are described in the paper.
本文描述步进电机微步控制的设计方法及驱动电路。
The newly designed backstepping control is implemented for permanent magnet synchronous motor (PMSM) to track speed commands, at the same time the design can provide better speed tracking performance.
设计的反推控制可以实现永磁同步电动机速度跟踪控制，保证系统具有良好的速度跟踪性能。
This paper introduces PC control approach of joint motion of manipulator. This approach includes driving of stepping motor, interface design of hardware circuit and software programming.
介绍一种机械手关节运动的PC机控制方法，它包括步进电机的驱动、硬件接口电路的设计、软件的编程方法。
Based on the design of the stepper motor control MCU.
本设计为基于单片机的步进电机的控制。
The experimental results verify that the proposed method is correct and feasible and it can simplify the circuit design of the motor control system.
实验结果证实所提出的实现方法是正确可行的，而且它可简化电机控制系统的电路设计。
Control of the hardware design part of the main controller, sensors and motor control circuits.
控制部分的硬件设计主要有控制器，传感器和电机控制电路。
The tension control system using permanent-magnet DC torque motor as executive component is design. It can inspect and adjust tension at real-time during winding.
设计了以永磁式直流力矩电动机为执行元件的张力控制系统，它能够实时检测和调整缠绕过程中纤维的张力。
Design a servo motor control system.
设计一种伺服电机控制系统。
The overall design is an accurate idea of the table and the safety of motor control.
设计的总体思路是准确安全的对工作台和电机进行控制。
Frequency conversion technology based on vector control theory, design of steel industry processing lines of induction motor driving program.
基于变频调速技术和矢量控制原理，设计钢铁行业处理线的交流异步马达的传动方案。
The paper introduces the hardware and software design of an AC servo motor control card based on 80C196KC.
介绍自行研制的基于80C196KC单片机的交流伺服电机控制卡的硬件设计及其软件实现。
This paper presents a software and hard ward design of a development and experiment platform for digital motor control based on TMS320F240 DSP.
介绍了基于数字信号处理器TMS320F240的数字化电机控制开发与试验平台的软硬件设计。
Introduction was made to basic structure and performance of DSP chip, giving out hardware design plan for induction motor vector control plan, software control algorithm.
介绍了DSP处理器的基本结构和性能，给出了感应电机矢量控制的硬件设计方案和软件控制算法。
The fuzzy control is an effective motor intelligent control technique, but there is no simple and intuitive design method.
模糊控制是一种有效的电机智能控制技术，但没有简单直观的设计方法。
Brushless motor control system design based on C8051 was introduced, speed and current double close loop control was realized.
论述了基于C8051的直流无刷电机控制系统设计，实现了速度、电流的双闭环控制。
This paper describes performance indexes, structure features, design method and experimental investigation of electrohydraulic servo motor with super-low-speed, wide speed control and high precision.
本文介绍了超低速、宽高速、高精度电液伺服马达的性能指标、结构特点、设计方法和试验研究。
A design of the open motion control system based on PC and motor control card was presented.
提出一种基于PC和运动控制卡的开放式运动控制系统的设计方案。
The design of step motor control card is based on DSP technique and PCI bus technique.
步进电机控制卡的设计采用了DSP技术和高速pci总线技术。
Based on the steady state equations of the motor for the design of VSVF, VSVF can control the torque to a certain extent, but it cannot implement the real control in the dynamic process.
转差频率控制能够在一定程度上控制电机的转矩，但它是以电机的稳态方程为基础设计的，并不能真正控制动态过程中的转矩。
This paper introduces a simple stepper motor control chip LMD18245. By using it, we can design the drive module of stepper motor by ourselves, and thereby decrease the cost of system design.
该文介绍了一种简单的步进电机控制芯片LMD18245，利用它可以自行设计步进电机的驱动模块，从而为系统设计降低成本。
The whole project design of the AC servo motor control system based on TMS320F2812 is introduced.
介绍了基于TMS320F2812交流伺服电机控制系统的整体方案设计。
The main objective of this design is the completion of the stepper motor control.
本设计的主要目标是完成步进电机的控制。
To better clarify the artificial heart design of the driving motor and control system, this article first detailed motor magnetic circuit system, classical design methods and formula of motor drive.
为更好的阐明人工心脏电机及控制系统的设计思路，一方面，本文详细阐述了磁路系统及电机经典设计方法及公式。
The design in this paper comes from a practical project of a spinnery. Our design and control object is the electrical spindle motor of weaving producing process.
本文的设计是来自于企业的一个实际的工程应用项目，设计控制对象为纺丝机电锭电机。
Using PWM to drive motor, and we design a circuit in DC serve control system.
利用PWM驱动方式控制电机的转动，并设计出了直流伺服控制系统硬件电路图。
Using PWM to drive motor, and we design a circuit in DC serve control system.
利用PWM驱动方式控制电机的转动，并设计出了直流伺服控制系统硬件电路图。
应用推荐