Then, the software design of the embedded motion controller which based on the PC/104 bus is analyzed.
再次，论文分析了基于PC/104的嵌入式运动控制系统的软件设计。
This paper introduces PC control approach of joint motion of manipulator. This approach includes driving of stepping motor, interface design of hardware circuit and software programming.
介绍一种机械手关节运动的PC机控制方法，它包括步进电机的驱动、硬件接口电路的设计、软件的编程方法。
Objective: To design a upper computer software which can achieve data acquisition, display, motion control for sickbed-control test system.
目的：为病床控制系统测试平台设计一种能够进行数据采集与运动控制的上位机软件。
In the paper the authors introduce the design methods of interactive software for analysis of motion and dynamics in plane linkage.
介绍了平面机构运动分析和力分析交互式软件的设计思想、设计功能与设计方法。
This paper presents an open software design of a DSP - based high - speed motion control system, which is applied in laser rapid - prototyping system.
描述以基于DSP处理器为核心，用于激光快速成型系统的高速运动控制系统软件的体系结构及其开放式设计。
The TMC428, which is a stepper motor motion controller, is a newest circuit of TRINAMIC Microchips GmbH. It is used to reduce the time of software design and the cost of production.
TMC428是TRINAMIC公司最新开发的步进电机运动控制器，它可减少电机控制软件设计的工作量，降低开发成本。
Finally, we analyse and design the software of digital motion control systems based on USB, including the firmware of USB device, the drivers of USB device.
最后设计开发了采用USB技术的数字运动控制系统的软件，包括USB设备固件程序、U SB设备驱动程序。
Part of software the motion target detection method based on timing difference has been researched, the software design has been completed.
软件设计部分，针对运动目标的检测跟踪各种跟踪方法，详细研究并实现了基于时间差分的运动目标检测方法，完成了系统整体软件设计。
The software includes the modeling, probe qualification, coordinates-setting, design of motion control system, path-planning of measurement and so on.
测量机的软件部分又包括测量数学模型的建立、测头的校正、坐标系的建立、测量运动的控制、测量路径的规划等等。
The software and hardware design of intelligent robot cutting system based on motion control card are discussed.
本文先容了基于行为节制卡的呆板人智能切割体系的软硬件计划。
This paper introduces the software and hardware design of CAN intelligent sensor node, which is used in a distributed motion control system.
介绍了应用于某分布式运动控制系统的CAN智能传感器节点的软硬件设计。
The motion function of robot is achieved by modularized software design. lt has been proved that the control-system has high reliability and it meets the requirement of use in practice.
软件采用模块化设计以实现了机器人运动功能。实验表明样机控制系统合理可靠。
A motion control system, specifically fit the differential drive nature of the tracked mobile robots, has been proposed, and corresponding design for both software and hardware are also given.
针对履带式移动机器人差动驱动的特点，提出了机器人运动控制系统的实现方案，并给出了相应的软、硬件设计方案。
A motion control system, specifically fit the differential drive nature of the tracked mobile robots, has been proposed, and corresponding design for both software and hardware are also given.
针对履带式移动机器人差动驱动的特点，提出了机器人运动控制系统的实现方案，并给出了相应的软、硬件设计方案。
应用推荐