The minimum thickness appeared in the bulging highest position.
最小厚度发生在鼓胀最高的地方。
The maximum layer thickness may not exceed twice the minimum thickness.
最大的涂层厚度值不能超过最小厚度的两倍。
The minimum thickness was mainly determined by the maximal internal pressure.
影响最小厚度的主要因素是最大内部压力。
Mini scan This is a minimum thickness scan and allows the user to run the probe over the wall surface.
迷你扫描这是一个最小厚度扫描并允许用户运行探针的墙面。
For any single layer within a system the actual thickness is permitted to be 10% less then the minimum thickness.
对仅由一层涂层构成的系统，实际的厚度可以允许比最小厚度值小10%。
When roughing, the user can specify a minimum thickness to machine. Areas smaller that this thickness will not be cut.
粗加工中，使用者可以设置最小留量，小于这个留量厚度的区域就不去加工了。
PC board inside the tablet series (universal, strong endurance plate) 150 times the minimum thickness of winding radius is itself;
答：PC板里边的平板系列（通用型、强力型耐力板）最小曲折半径是是本身厚度的150倍；
For a stone arch bridge with a given arch centre line and a given loading condition, there exists a minimum thickness limit for the arch ring.
给定拱轴的石拱桥，对应于每个荷载工况，拱圈有一个最小极限厚度。如果拱圈厚度等于或小于这个极限，石拱将出现三个以上的铰而破坏。
The new conveyor system composed by rolls and flat belts makes this unit particularly suitable for the management of flexible or of minimum thickness panels.
改良的转向器系统由滚轮和传送带构成，使得该机器特别适合软板和薄板操作。
In numerical simulation minimum thickness was taken as forming limit criterion. The research on the relation between minimum thickness and strain paths was carried out.
在数值模拟中应用最小厚度作为成形极限判据，研究最小厚度值与应变路径的关系。
Therefore, a minimum wall thickness can be established by experience for various shapes, materials, and process combinations.
因此，对各种形状，材料和工艺组合能通过经验来确定最小壁厚。
She derived another formula relating the number of folds possible in one direction (n) to the minimum possible length of material (l) and the material's thickness (t)
她推导出了另一个关于折叠次数（n）、现实的最小长度（l）以及材料厚度（t）的关系式。
Dimensions, thread gaging, minimum wall thickness and burst pressure, material classification, various quality aspects and requirements for marking identification are stipulated.
尺寸，螺纹规，最小壁厚和爆裂压力，材料分类，各种质量要求和所规定的标记和标识要求等。
The results show that there are obvious changes at film pressure distribution, maximum film pressure, film thickness distribution and minimum film thickness when there is misalignment.
计算结果表明，轴颈倾斜时，轴承油膜压力分布、最大油膜压力、油膜厚度分布和最小油膜厚度等都有明显的变化。
Thread dimensional specifications, minimum wall thickness and burst pressure, material classification, and requirements for marking identification were stipulated.
螺纹尺寸规格说明，最小壁厚和爆裂压力，材料分类，以及规定的标记标识的要求等。
It can measure the oil film thickness, oil temperature, crank Angle, speed, journal center locus and minimum oil film thickness of main bearing in diesel engine.
该系统可测量内燃机主轴承的油膜厚度、油膜温度、曲轴转角、转速、轴心轨迹和最小油膜厚度。
The position of minimum values on the sound transmission loss curve varies with the changes made on plate thickness and the moment of inertia of stiffeners.
板厚或肋骨惯性矩的变化会引起结构传声损失曲线上隔声低谷位置的变化；
The location of soleplate line and the thickness the minimum rock cover are further studied through numerical simulation.
根据数值模拟结果进一步确定象山港海底隧道的底板线位置和最小岩石覆盖厚度。
This paper introduces the method of calculating minimum oil film thickness between teeth of gear pump on the basis of elastohydrodynamic lubrication theory, with achieving computer-aid-analysis.
本文根据“弹流”理论，介绍了计算齿轮泵齿间最小油膜厚度的方法，并且实现了计算机辅助分析。
Thickness is the minimum dimension of the heaviest section of the part.
厚度是最大截面上的最小尺寸。
At last, the formulation of allowable minimum bending radius limiting the change of the tube-wall thickness is derived, and proved to be of practical value.
推导出限制弯管壁厚变化量的许用最小弯曲半径公式，经试验验证具有一定的实用价值。
The minimum reliable thickness of a mill is a parameter which is obtained under the limited rolling condition.
轧机的最小可轧厚度是说明轧机极限轧制条件的一个参数。
All expansion joints shall have bolted flange-to-flange type connections on both sides of expansion joint for removal of complete unit. Minimum flange thickness shall be 6 mm.
所有的伸缩接头(膨胀节)都应当采用法兰栓接。法兰的最小厚度为6毫米。
Using the results of this analysis and calculations, A more accurate minimum film thickness formula is presented and its error is generally less than 0.5%.
根据分析和计算的结果提出了一个较准确的最小膜厚公式，其误差一般小于0.5%。
The minimum reference value of the wall thickness of GF/PP products with different content of GF was obtained.
得出了不同含量玻纤增强PP挤出吹塑制件的最小壁厚的参考值。
At the same time, it also discusses the effect of operation parameters of gears on minimum oil film thickness.
同时，讨论了齿轮泵工作参数对最小油膜厚度的影响。
At the same time, it also discusses the effect of operation parameters of gears on minimum oil film thickness.
同时，讨论了齿轮泵工作参数对最小油膜厚度的影响。
应用推荐