NC milling time and quality were also improved.
数控铣时间和质量也有改善。
With the milling time increased, the hydriding properties are improved.
延长球磨时间，可改善合金的吸氢性能。
The effect of different milling time on performance of W-Cu composites was investigated.
研究了不同球磨时间对钨铜复合材料性能的影响。
The influence of ball milling time on hydrogen storage performance was also investigated.
研究了材料的组成和球磨时间对吸放氢性能的影响。
There was significantly negative relationship between embryo surviving rate and milling time.
胚残存率与碾精时间呈极显著负相关。
Coarse, medium and fine WC powders are used for tests at different ball percentage and milling time.
试验中采用粗、中、细3种碳化钨粉末进行了不同球料比、不同球磨时间的试验。
The results show that with the increase of milling time, particle size and crystallite size are reduced.
结果表明，随着球磨时间的增加，粉末的颗粒度及晶粒度均不断减小。
It is found that Mosaic fragment size and length range order parameters decrease with increase of milling time.
发现随球磨时间的增长，嵌镶碎块尺寸和长程有序度同时减小。
The results show that the milling time has significant effect on the powder structure and particle configuration.
结果发现，球磨时间对混合粉末的结构及颗粒形貌存在显著影响。
The effects of sintering temperature, holding time, and milling time on the tribological properties were also studied.
研究了烧结温度、保温时间和球磨时间对放电等离子烧结合金耐磨性能的影响。
Milling time and annealing heat treatment are the main influencing factors for changing powder structure and fining grain.
球磨时间和退火热处理是粉末金相组织变化和晶粒细化的主要影响因素；
Methods: the effect of adhesive concentration, milling time and pressure on the dissolution of Nimesulide tablets were studied.
方法考察粘合剂浓度、研磨时间、压片力对尼美舒利片溶出度的影响。
It is studied that milling time, carbon content, inhibitor and sintering effect on properties of the submicron cemented carbides.
研究了球磨时间、碳含量、抑制剂以及烧结对超细硬质合金性能的影响。
The results show that an alloy may be formed by ball-milling and amorphous character is enhanced with the increasing of the milling time.
结果发现，球磨可形成合金化，随球磨时间的增加，样品的非晶化逐渐加强。
Abstract: It is studied that milling time, carbon content, inhibitor and sintering effect on properties of the submicron cemented carbides.
文摘：研究了球磨时间、碳含量、抑制剂以及烧结对超细 硬质合金性能的影响。
In addition, no agglomerated powders were detected and no in-plane fragmentation occurred. But the D03 structure disappeared with long milling time.
球磨改变了合金微粉的相结构，使有序D03相随球磨时间的延长逐渐消失。
The effects of milling time and sintering temperature on density, hardness, transverse rupture strength and compressive strength were mainly studied.
重点研究了球磨时间和烧结温度对烧结合金的密度、硬度、横向断裂强度和压缩强度的影响。
The sequence of the factors was determined by orthogonal experiments: ball gradation, milling rotational speed, ball milling time, and ratio of ball to powder.
正交试验表明四个因素的主次顺序为：磨球级配、球磨机转速、球磨时间、球料比。
The results show that the increase of the milling time, the vibration frequency and the charge ratio can effectively decrease the grain size of the alloy powder.
结果表明：球磨时间延长，振动频率提高和球料比的增大可有效地降低合金粉的晶粒尺寸。
The results show that when the high-energy mechanical milling time increases, the relative density of pressed compact decreases gradually under the same compacting pressure.
结果表明，压制压力相同时，粉末压坯相对密度随高能球磨时间的延长而逐渐减小。
As dielectric constant of samples decreases with increasing the ball milling time, impedance matching becomes better and the performances of microwave absorption are promoted.
由于随球磨时间增加样品介电常数下降，使得阻抗匹配变好，样品的微波吸收性能提升。
The simulation results show that, with increasing the milling time, the densification of powders becomes more and more difficult, and the needed extrusion pressure substantially rises.
分析结果表明，随着球磨时间的延长，粉末固结致密难度增加， 所需挤压力显著增大。
When charge ratio and milling time were constant, the average particle size of the powder decreased with the increase of rotation speed, while the amount of small size particles increased.
在相同球料比和球磨时间下，粉体平均颗粒尺寸随球磨转速增加而减小，其中的小颗粒数目也增多。
Wi th the milling time increasing, the microhardness decreases a little at first, and then rapidly increases, in the end it keeps a constant when amorphous microstructure is basically formed.
随球磨时间的延长，粉末显微硬度开始略有下降，然后迅速增加，在基本形成非晶后，保持恒定值。
In view of low milling efficiency, the effect of milling form, loading coefficient of materials, rotational speed of ball mill, milling time and grinding aid on milling efficiency was discussed.
针对陶瓷生产中球磨机效率低的问题，从工艺上讨论了研磨方式、物料的装填系数、球磨机转速、研磨时间以及助磨剂对球磨机效率的影响。
The relative density of pressed compacts, which were prepared by high-energy milling 3%c-cu powders with the same high-energy mechanical milling time, increases with increasing compacting pressure.
高能球磨时间相同时，粉末压坯相对密度随压制压力的增加而增大。
"Much time was spent milling the existing dimensions," the team said.
“花了很多的时间磨成现有的尺寸，”团队说。
Properties and morphology of thermites mixed up by twin-screw and ball milling procedures are investigated with different mixing time.
采用双螺旋和球磨两种混料方式，研究不同混料时间对（铝）热剂性能及颗粒微现形态的影响。
The time of starting reaction is 24 to 24.5 hours of milling.
在本实验条件下，反应的触发时间在球磨24小时到24.5小时之间。
The time of starting reaction is 24 to 24.5 hours of milling.
在本实验条件下，反应的触发时间在球磨24小时到24.5小时之间。
应用推荐