The development of mill load measurement instrument based on DSP was discussed.
介绍了基于DSP的磨机负荷检测仪的研制。
One of the reasons is that there is still not a practical and accurate method to measure the coal storage (or mill load) of the mill.
原因之一就是至今还没有一种实用、准确的方法对磨煤机内的存煤量(磨负荷)进行测量。
To minimize costs, expansibility of available DCS was fully utilized in the hardware and software implementation of cement ball mill load control system.
在控制系统的硬件和软件实现上，充分利用水泥厂现有DCS的可扩展性，降低了系统的成本。
The energy-saving effects of low-temperature rolling, effect of low-temperature rolling on product quality, mill load and aspects to be noted on low-temperature rolling production are discussed.
叙述了低温轧制的节能效果、低温轧制对成品质量的影响、低温轧制对轧机负荷的影响及低温轧制在生产中应注意的问题。
This eases operator work load when checking a repetitive number of identical encoders such as on a production line or in a mill environment.
这简化了操作员的工作量，在检查了相同的编码器，例如一条生产线或在工厂环境中不断重复的数字。
These bearings have a particularly high axial load carrying capacity and are used primarily as thrust bearings in rolling mill applications.
这些轴承有特别高的轴向负荷能力，主要用作轧钢机里的推力轴承。
Based on the rolling feature and practice of reversible cold mill, a new calculating method to determine the load distribution is put forward by means of nonlinear equations.
根据可逆冷轧机的生产特点，采用一种通过直接求解非线性方程组来确定负荷分配的方法。
The testing method and data processing procedure for random load on the transmission system of a BED type ball mill with straight flow are presented.
介绍了直燃式双进双出钢球磨煤机传动系统随机载荷的测试方法及数据处理步骤。
The load rate, load fluctuation rate and actual distribution of the torque moments of partial spindle of the mill have been analyzed.
分析了三辊劳特式轧机的负荷率、负荷波动率水平及分轴扭矩的分配实况。
A rolling load distribution optimization algorithm of tandem cold mill was designed using particle swarm optimization algorithm.
利用粒子群算法设计了一种冷连轧轧制负荷分配的优化方法。
Four-point contact ball earings used for rolling mill roll the oil tank to withstand the axial load.
四点接触球轴承多用于轧钢机的油辊箱以承受轴向负荷。
Allowing more coal through a mill at a required fineness is beneficial as it allows a mill to contribute more MW to the required boiler load.
让更多的煤在所需要的细度下通过磨煤机是有利的，因为它允许磨煤机贡献更多的兆瓦来提高锅炉负荷量。
Based on the rolling feature and practice of reversible cold mill, a new calculating method to determine the load distribution is put forward by means of nonlinear equations.
根据可逆冷轧机的生产特点，采用了一种简单的迭代方法求解负荷按比例分配构成的非线性方程组，得到总轧制道次数以及各个道次的中间厚度。
An aggregate equal load function was developed and applied to the load distribution on a double-stand mill during hot strip rough rolling.
针对带钢热连轧双机架粗轧机组的特点，应用综合等负荷函数法进行负荷分配。
The screwdown block is improved by mechanics analysis with boundary element method, and a simple device is designed for dynamic load of oil film bearing used in high-speed wire rolling mill.
通过采用边界元法对高线轧机压下垫块改造模型进行力学分析，开发设计一种适合测量高线轧机油膜轴承动态载荷特性的简易装置。
Experiments indicate that it can make the throughput increased clearly, and can make the ball consumption and load reduced clearly that the mill outlet is properly reduced.
试验表明，适当缩小出料口，处理量明显增加，而钢球消耗和负荷确明显减少和降低。
The paper presents a mathematical model for the high consistency refining process of Fujian Qingzhou paper mill based on the specific edge load theory. The validity of the model has been confirmed.
根据比边缘负荷理论，建立了福建青州造纸厂高浓打浆过程的数学模型，并证实了模型的正确性。
With the improvement of unit load and parameters of the power plant, coal-fired power plant USES medium speed mill direct-firing pulverizing system in common.
随着火电机组容量和参数的不断提高，火电厂普遍采用中速磨直吹式制粉系统。
General loading condition of rolling mill bearings is medium - heavy load and shock load, thus the most suitable material is carburising bearing steel.
轧机轴承一般载荷条件是中重载荷和冲击载荷，因此，最适用的材料为渗碳轴承钢。
Efficient removal and recovery of the soluble material from cooked pulp is important to minimize chemical makeup, requirement, bleaching demand, and pollution load in the mill effluent stream.
从蒸煮所得的纸浆中有效的提取并回收溶解物质，对最大限度的减少补充化学药剂、减少漂白剂的需要量、降低工厂废水的排污负荷，均具有重大的意义。
A new over-long pipe cold drawing mill with three pipes drawn simultaneously, which has an unique structure and a display device for drawing load, is described.
本文介绍了一种结构独特，可显示拔制负荷的新型超长三线冷拔机。
Based on experiment data, a model for the relationship between the rolling load of an open mill and its affected factors was built with artificial neural networks.
在实验数据的基础上，利用人工神经网络建立开炼机横压力与其影响因素之间对应关系的数学模型。
And commissioning follows no load debugging of every system as main reducer lubrication system, roller mill pressure station and roller lubrication system.
磨机负荷试运行阶段，主要探索使系统稳定运行的系统风量、磨机压差、入磨气体压力等工艺参数的控制。
Aiming to the crane load (Q) importance in control single story mill building design.
针对吊车起重量(Q)在控制单层工业厂房设计中的重要性。
The productivity of mill, separating indexes of dressing process are increased, and the consumptions of materials and power are decreased by adoption of the accurate method for ball load and addition.
新的装补球方法提高了磨机生产率及选别指标，并降低了球耗和电耗。
Electro Hydraulic Servo Valve is key component in roll load system of aluminium foil rolling mill. This paper introduces the principle and maintenance of Electro Hydraulic Servo Valve...
电液伺服阀是铝箔轧机压上电液控制系统中的关键零部件。在介绍电液伺服阀工作原理的基础上，就其使用与维护要素作了阐述。
An new experimental method of measuring load has been developed for oil film bearing on strip rolling mill.
通过对轧机油膜轴承锥套载荷分布的模拟实验研究，给出了轧机油膜轴承锥套载荷测试的新方法。
After load observer put into use, it has a good actual results to suppress the mill stand vibration.
投入负荷观测器后，对抑制轧机振动起到了良好的实际效果。
The effective clearance of operating slide in plate mill possesses the actions of load bearing and presenting.
中板轧机滑板的有效间隙具有承载和导向作用。
This paper describes the practical significance of removing peak and filling valley load on the grinder of cement mill.
本文阐述了水泥工业实现磨机移峰填谷的重大意义；
应用推荐