The microhardness of the coating was measured.
测试了涂层的显微硬度。
The hardness was measured by the microhardness tester.
用显微硬度仪测试了试样的显微硬度。
The microhardness increases remarkably near the interface.
界面区显微硬度显著提高。
The roots were sliced and root-dentin microhardness was measured.
用微硬度测定仪检测根管牙本质的微硬度。
Methods: Tension test machine and microhardness tester were used.
方法：用拉力机、显微硬度机测试。
The microstructure, microhardness and depth of the nitrided layers were studied.
对渗氮层的硬度、深度和组织结构等进行了分析研究。
Microhardness on the surface layer were measured by microhardness testing machine.
利用显微硬度试验机来测量表面显微硬度。
The surface microhardness was substantially increased compared with the untreated.
表面显微硬度较未处理的样品明显提高。
The feasibility of this method is confirmed by comparison with microhardness method.
在与硬度法的对比试验中，进一步验证了电阻法的可行性。
Moreover, when CO2>30%, the process stability and microhardness of weld dramatically decrease.
当CO2含量>30%后，复合焊接工艺稳定性变差，焊缝硬度急剧降低。
The microstructure, microhardness and dry-sliding wear resistance of the coating were evaluated.
并对涂层的显微组织、显微硬度和室温干滑动实验进行了具体分析。
Microhardness testing during aging treatment in high purity steel bearing copper was carried out.
对经时效处理后的含铜高纯钢进行了显微硬度测试。
In addition, the trend of microhardness variety could not accord with the ultra-plastic wave formula.
合金的显微硬度变化趋势不符合超塑性波动公式。
The effect of heat treatment temperature on the microhardness and magnetic properties were investigated.
研究了热处理对镀层显微硬度和磁性能的影响。
The layer is smooth with higher microhardness, corrosion and bonding strength by using the proper process.
在合适的电刷镀工艺下，镀层表面平整、光滑，具有较高的显微硬度、耐蚀性和结合强度。
The results show that the parameters have great effect on microstructure and microhardness of the coatings.
结果表明，工艺参数对冶金层显微组织及显微硬度有很大的影响。
The microhardness and surface roughness of specimens before and after shot peening was studied and analysed.
分析研究了喷丸强化处理前后的显微硬度和表面粗糙度。
The microhardness test was used to determine the behaviour and the extent of the interfacial transition ring.
本文还通过显微硬度试验测得界面过渡环的性状及范围。
The microhardness value of the amorphous alloy is lower than that of the crystalline alloy with the same composition.
显微硬度测试表明，对相同成分合金，非晶态的显微硬度值比晶态的低。
The high frequency induction hardening can't raise the surface microhardness of the cold precision forging spur gear.
高频感应淬火不能达到硬化冷精锻直齿圆柱齿轮齿面的目的。
The depth and microhardness distribution of alumetizing layer obtained on different technical conditions were measured.
测定了不同工艺条件下获得的浸渗层深度和浸渗层显微硬度的分布。
The flexural strength and hardness of the specimens were tested with an instron testing machine and a microhardness tester.
分别以应力分析仪和显微硬度仪测试两组试件的挠曲强度和硬度值。
The fractured springs were analyzed by means of SEM, metallography, chemical composition analysis and microhardness measurement.
采用扫描电镜、光镜、化学成分分析和显微硬度测试等方法对断裂件进行了分析。
Objective To investigate the influence of fluoride foam of different concentration on microhardness of demineralized enamel surface.
目的观察不同浓度氟泡沫对脱矿牙釉质表面显微硬度值的影响。
The microhardness of nitriding layers obtained in a wide range of treatment temperature is 5 ~ 6 times higher than that of the substrate.
可在较宽的温度范围内对该钢进行脉冲直流等离子渗氮，获得表面硬度高于基底5 ~6倍的渗氮层。
These results indicate that the microhardness of crystals depends not only on the crystal structure and lattice energy but also on temperature.
最后指出晶体硬度不仅与晶体的结构、晶格能有关，而且也与温度的影响有关。
These results indicate that the microhardness of crystals depends not only on the crystal structure and lattice energy but also on temperature.
最后指出晶体硬度不仅与晶体的结构、晶格能有关，而且也与温度的影响有关。
应用推荐