Traditional method of Deformation prediction is based on a single model.
传统的变形态势分析大都是基于单个模型进行的。
In this paper, the formulae for the solution method of deformation vectors are derived and the precision formulae are also given.
在建立滑坡外部变形测边三维监测网的探讨中,推导出了变形向量的解算公式,并给出了精度估算公式。
Meanwhile, prediction model of underground deformation and predicting method of deformation for special geological factor is deduced under combined mining with random medium theory.
同时应用随机介质理论,推导出复合采动影响下地面变形的预测模型和特殊地质条件下变形的预测方法。
A calculation method of the flattening in sheet rolling deformation zone, using influence function, was derived.
采用影响函数法推导了薄板轧制时变形区内轧辊弹性压扁的计算式。
Through this method, the large-scale dynamical displacement can be measured and the process of deformation in surface can be analyzed.
运用这种方法不仅可以测量大动态范围的面内变形,而且可以测量分析面内动态变形过程和变形速度。
The stress characteristic of the interface, deformation rule under the action of load and the stress distribution rule were discussed by adopting the experimental research method.
采用实验研究的方法,探讨锚固体界面力学特征、在荷载作用下变形规律以及界面上的应力分布规律。
Based on construction practice, the paper analyzes deformation of railway embankment in permafrost zone in Qinghai-Tibet Plateau, centering on monitoring method for embankment deformation.
结合工程实例,简要分析在青藏高原多年冻土区修建的铁路路堤易遇到的变形问题,重点探讨路堤变形的监测方法。
The structure and load form of the absorbing tower is complex and regular design and calculation method cannot give its distribution condition of the stress and deformation.
脱硫吸收塔结构及荷载形式复杂,常规设计计算方法不能给出其应力和变形分布情况。
And there is also simplified method using modulus of deformation by considering constitutive model of soil to calculate settlement.
也有考虑土的本构关系,用其变形模量进行计算的简化方法。
Based on the characteristics and the deformation destroying of high embankment, the main reasons for the deformation destroying are analyzed and the method to resolve the problem is suggested.
根据高填路堤的特点及其变形破坏的表现形式,深入分析了高填路堤变形破坏的主要原因,并提出了高填路堤变形破坏的处理对策。
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析;
A new method for analyzing the time-dependent convergence deformation of the underground surrounding rock is presented.
研究了地下洞室围岩的时间效应变形特性,提出了分析围岩时间效应收敛变形的一种新方法。
At the same time, analyze the welding deformation of straight-line segment model of side rail, and compare the results with test data, verify this method is efficient.
同时,针对汽车纵梁部分直线段模型进行焊接变形分析,并与试验数据进行了对比,验证了该方法的有效性。
This method can be used to analyze accurately the complete load-deformation response of RC beams loaded in combined shear, moment, and axial load.
该法可以对在弯矩、剪力和轴力共同作用下的钢筋混凝土梁截面进行较为准确的荷载-变形反应全过程分析。
With the non-line finite element method, the numberical value calculation on the stress and deformation of surrounding rock of deep mine roadways has been presented.
采用非线性有限元法,对深井巷道围岩应力及变形状态进行了数值计算。
This paper presents the principle of conjugate beam method which can be applied to the calculation of deformation.
本文介绍了用于梁变形计算的共轭梁法的原理,并举例说明了该方法的应用。
An equivalent stress method for the structural analysis of derrick with initial deformation is offered.
为此,采用等价应力法对有初始变形的井架进行结构分析。
Based on genetic programming (GP) theory, the mathematical modeling method of dam deformation monitoring is researched.
研究了基于遗传规划(gp)理论的大坝变形监测数学模型的建模方法。
Using the proposed technique the measurement and calculation method of material mechanical deformation direction is described. Finally, the experimental results and test data are given.
给出了一般情况下用本技术测量和计算材料机械变形方向的方法,列出了本技术测量的实验数据和结果。
Combining with the relative movement parameters, a deformation analysis method of successive approximations is presented.
结合相对运动参数,提出了一种逐渐趋近的变形分析方法。
The method can reflect nonlinear deformation behavior of soil and is more close to the real situation.
该方法可以考虑土的非线性变形特性,也更符合土的实际情况。
In this new method the influence of transverse and squeeze deformation was considered, the basic equations are complacated easily like classical theory.
该方法计入了板的横向剪切变形和挤压变形影响,其基本方程如同经典理论一样简单易解。
The comparison of results obtained from this method with experiment and incremental approach indicated that this method can analyze the deformation of sheet metal forming part qualitatively.
通过实例的计算结果和实验以及增量方法进行了比较,表明此方法能够定性地分析成形工件中的变形情况。
Aiming at the disadvantages of experience formula, the case-based SVM method for maximal deformation forecasting of surrounding rocks of tunnels is proposed.
针对经验公式方法的不足,提出基于工程实例的隧洞最大允许变形的支持向量机(SVM)自动获取方法。
The conventional method of testing the shed drawing deformation of travellers is of poor precision and difficult operation.
目前纺纱用钢丝圈开口拉伸变形率的测量采用人工方法,精度低,操作困难。
The quick design process of electrode and the method of the avoiding deformation in reinforced electrode manufacture are introduced, the aim is to shorten the cycle of die manufacture.
介绍了电极的快速设计过程与防止薄筋电极加工时发生变形的方法,最终达到缩短模具制造周期的目的。
By the treatment method it solves problem on deformation of wall and bottom plate relative to bow - shape edge plate and ensures engineering quality.
采用这种方法解决了更换底圈壁板必然涉及的壁板、底板(弓形边缘板、中幅板)变形问题,保证了工程质量。
By the treatment method it solves problem on deformation of wall and bottom plate relative to bow - shape edge plate and ensures engineering quality.
采用这种方法解决了更换底圈壁板必然涉及的壁板、底板(弓形边缘板、中幅板)变形问题,保证了工程质量。
应用推荐