Disconnect Figure 3 c, d, the use of manometry to circuit (or leakage measurement method) to find the fault has shifted the cylinder.
断开图3中的C、D处，利用、回油路测压法(或测泄漏量法)找到了有故障的转向缸。
The structural dynamic response of a certain multi? cylinder internal combustion engine block is analyzed applying finite element method.
应用有限元方法对某多缸内燃机机体在活塞推力作用下的结构动力响应进行了分析。
Design method to enhance fatigue strength of a dome is given without increase of total cylinder mass.
在不增加气瓶总质量的情况下，得到了提高封头疲劳强度的设计方法。
Computation and analysis of the cylinder block stress and deformation are conducted on a 6125q diesel engine in supercharged or cylinder diameter enlarged situation by using the finite element method.
本文应用有限元法，对6125Q型柴油机机体在增压和扩缸时的变形和应力进行了计算分析。
The room temperature resistivity of samples was measured by cylinder method.
用圆柱体法测量了样品的室温电阻率。
Pneumatic PWM position servo system is nonlinear system. The satisfied results are difficult to be obtained with traditional control method while the friction force of cylinder is large.
气动脉宽调制位置伺服系统是非线性的系统，在气缸摩擦力较大的情况下，采用传统的控制方法难以取得满意的效果。
On the bases of comparing against routine processing method, clarify the superiority of powder metallurgy forming for the miniature cylinder.
在与常规加工方法比较的基础上，阐明了该微型气缸采用粉末冶金方法成形的优越性。
A simple testing method of wear resistance for piston ring and cylinder sleeve is introduced.
本文介绍一种简易的活塞环与气缸套磨损试验方法。
Piston, method for manufacturing the same, and cylinder component with the same.
活塞，用于制造该活塞的方法，和设置有该活塞的缸组件。
The test of external pressure is studied for steel-walled pressure cylinder by using reliability method. The relation of external pressure test and influencing factor is analyzed.
应用可靠性设计方法，对钢制外压圆筒形容器压力试验进行了研究，定量分析试验压力与影响因素之间的关系。
Stress distribution at cross section of transverse uniformly distributed load and non-uniformly distributed load applied to concrete cylinder by finite element method is analyzed.
采用有限元的方法计算分析了混凝土圆柱体在受横向均匀线荷载和非均匀线荷载时其横截面上的应力状况。
A novel cylinder pressure recognition method for internal combustion engines is proposed.
提出了一种新的内燃机气缸压力识别方法。
A diagnostic method for diagnosing a diesel engine cylinder faults according the engine transient speed waveform and gas pressure torque waveform is presented in the thesis.
本文讨论了基于柴油发动机瞬态转速波形和气压扭矩波形对柴油机气缸内故障进行诊断的方法。
Analysis and comment are made on the floating cylinder sleeve method known in late years.
对近几年来发表的浮动缸套测量法进行了分析和评述。
This paper analyses several methods of cylindrical measures, based on their advantages and disadvantages, adopt the absolute measure's method in cylinder as the basic theory.
在分析了几种柱面测量方法优缺点的基础上，选用柱面绝对检验方法作为测量柱面的理论基础。
By applying fuzzy optimal design method to cylinder helix spring design, the mathematical model of fuzzy optimal design in cylinder helix spring is established.
将模糊优化方法应用于圆柱螺旋弹簧设计，建立了圆柱螺旋弹簧模糊优化设计的数学模型。
A method of synchronous testing for long travel multi cylinder is proposed in this paper.
提出一种长行程多油缸的同步测试新方法，并与计算机相结合，实现了实时检测。
The stress and displacement distributions of the bellows under torsion loading are investigated by using both finite element method (FEM) and equivalent cylinder method.
本论文分别采用有限元法和等效圆筒法对波纹管在扭转载荷作用下的应力分布和位移变化情况进行了计算。
This paper introduces the repair welding procedure for repairing an alumal casting piece of an oil pump cylinder, This method covers the shortages of AC argon arc weld and gas welding.
介绍了对油泵机缸体铝锰合金铸造件缺陷补焊修复的技术工艺，且弥补了若采用交流氩弧焊和气焊施焊时存在的不足。
The merits of complex method and its application to optimum design of cylinder under superhigh pressure are discussed.
本文概略地介绍了复形法的优点及其在超高压容器优化设计中的应用。
This paper presents a practical method to calculate the pressure angle at pitch cylinder, of gear drive with computer.
本文提出了一种利用计算机计算齿轮传动啮合角的简便易行的方法。
A new method employing rigid cylinder-shaped stylus for measuring the errors of involute tooth profiles of gears is presented. Its principle and measuring results are introduced.
提出一种采用刚性圆柱棒形测头测量渐开线齿形误差的新方法，介绍了测量原理及测量结果。
A new centering and clamp method was introduced in this text by processing of cylinder surface of pump shell.
通过泵壳在立车上径向外圆的加工，介绍了一种新型的找正、装夹方法。
Analyse choice method of collision point of cylinder and shovel head and confirm initial pressure and volume of nitrogen chamber.
分析了活塞杆与铲头碰撞点的选择方法和氮气室的初始压力和初始容积的确定方法。
According to the new cylinder detection method, the cylinder detection system is designed.
根据新的圆筒检测方法，设计了圆筒检测系统。
The design method of hot-press for producing the hard pressboard cylinder is introduced and the calculation method of its structure strength is presented.
介绍了硬纸筒加工用热压机的设计方法，其中对结构强度的计算方法作了重点介绍。
By using the light ray vector method, the elliptic-section cylinder lenses have been designed to collimate the semiconductor laser beam.
采用光线矢量法设计了两个相互垂直的椭圆截面柱透镜组来准直半导体激光束。
A sleeve antenna mounted on metallic cylinder is analyzed by moment method.
采用矩量法分析了安装在金属圆柱筒上的套筒天线。
A sleeve antenna mounted on metallic cylinder is analyzed by moment method.
采用矩量法分析了安装在金属圆柱筒上的套筒天线。
应用推荐