The filter equiped with a melt pressure sensor could avoid wrong change and decrease the melt pressure by 30 %.
安装料压传感器，可避免漏换和错换，并可降低熔体压力30 %以上。
In consideration of melt pressure, the circular plate thickness can be calculated in accordance with the formula.
考虑熔体压力，圆形板厚度可由公式算出。
Extrusion rate, melt pressure, flow profile and mixing effects of the conical twin screw with mixing elements were observed experimentally.
对混炼型锥形双螺杆的挤出产量、物料压力、物料流动状态及混合效果进行了大量实验研究。
PET-FDY was prepared by using combination equipment. The effect of chips drying condition, spinning temperature, melt pressure and cooling condition on the quality of FDY was discussed.
用嫁接设备纺制涤纶FDY，讨论了切片干燥条件，纺丝温度，熔体压力，冷却成形条件等对FDY质量的影响。
The result of experiment showed that the anti aging effect of the composites was good, and using this antioxidant could solve the aging of SIS in the hot melt pressure sensitive adhesive.
结果表明：新型防老剂抗老化效果较好，可解决热熔压敏胶中SIS的老化问题。
They note that pressure and the temperature inside the reactor core remain at levels far lower than what would further melt the core.
他们指出，该反应堆堆芯现在保持的压力与温度并不高，远远低于会导致堆芯进一步融化的水平。
The molder must recognize the dangers of excessive fill speed, insufficient injection pressure, excessive melt temperature, and inadequate packing.
注塑工必须认识过快填充速度、不足注塑压力、过高融化温度和不充分挤压的危害性。
The head pressure increases when the melt viscosity and temperature decreases, so the products will have good shape and favorable stability.
温度降低时，熔体黏度大，机头压力增加，挤出制品压的较密实，形状稳定性好。
Exercise didn't simply melt away the stress-bosses who worked out reported feeling just as much pressure as their sedentary counterparts.
锻炼不是简单地消除压力——喜欢锻炼的老板和经常久坐的老板感受到的压力是一样的。
Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.
加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。
Although the interface has the features of melt, and pressure welding, the molten and diffusion welding cannot explain the bonding mechanism of explosive welding.
实验表明，爆炸焊接界面虽然具有熔化、扩散和压力焊的特征，但不能用熔焊和扩散焊机理来解释爆炸焊接界面的成因。
The effects of pressure and frequency on ABS samples of different melt temperature under vibration field were studied.
研究了在振动场作用下，ABS试样在不同的温度熔体下受振动压力和频率的影响。
After simple introduction the advance in silicate structure research, the influences of components, temperature and pressure on melt structure are discussed in detail.
本文概括介绍了熔体结构的研究进展，着重讨论了熔体组分、温度及压力对熔体结构的影响。
The change of oligomer content was analyzed at static high-pressure state during polyester melt transfer course in screw extruder and pipes.
研究了聚酯熔体在螺杆输送、管道输送过程中及静态高温状态下齐聚物含量的变化。
The effects of various factors on the desulphurization of melt were studied by changing gas species, gas pressure and melt polarity.
通过改变气体种类、压力和熔体极性，研究了各种因素对熔体脱硫的影响。
The effects of the moisture content in polyester chip, the melt temperature and pressure, and the shear rate on the shear viscosity are discussed.
探讨了聚酯切片含水率、熔体温度、熔体压力、切变速率对熔体切变粘度的影响。
The processing parameters of PEEK composites include cooling rate, forming pressure, forming temperature and the holding time in melt.
其成型工艺参数包括冷却速度、成型压力、成型温度、保温时间。
The interface motion situation of gas-melt is changed when injecting gas into melt in various conditions-gas-entering pressure, melt temperature and so on.
气体经喷嘴进入聚合物熔体时所形成的气熔界面的运动情况随着进气压力、熔体温度等不同参数的改变而发生变化。
The melt filling stage is one of the most important stages of the polymer molding; this stage involves the variation of the pressure and the movement of the front interface.
熔体充填过程是聚合物成型过程的一个重要阶段，该阶段涉及型腔内的压力变化及熔体前沿界面问题。
The high-pressure core melt accidents in PWR nuclear power plant which cover most of the severe accidents, have large potential risk.
压水堆核电厂的高压熔堆事故覆盖了大部分的严重事故序列，且具有很大的潜在威胁。
The quality of the hollow blow molding plastic products is affected by various process factors, such as melt temperature, inflation pressure, stretching rate, cooling time and polymer property, etc.
中空制品的吹型成型质量受各种工艺因素的影响，包括熔融温度、吹胀压力、拉仲速率、冷却时间、聚合物材料柱能等。
Flow distribution plate and the nozzle and the injection molding machines are connected, the injection of molten plastic melt by heating the shunting plate pressure evenly distributed to each nozzle.
分流板与喷嘴和注塑机连接，将注塑出来的熔融状态的塑胶熔体通过加热的分流板压力均匀分流到各个喷嘴。
So it is widely applied to pressure-sensitive adhesive, hot-melt adhesive, traffic paint, viscosity increaser for rubber, printing ink, hydrophobic agent for paper etc.
因此，被广泛应用于压敏胶粘剂、热熔性胶粘剂、交通路标漆、橡胶增粘剂、涂料、印刷油墨、纸张的疏水剂等。
The effects of the protrusion length of the melt delivery tube and the atomization gas pressure on the average particle size and fine powder yield were studied.
本文以紧耦合气体雾化技术对这一粉末进行研制，分别研究了导液管伸出量、雾化气压对粉末的平均粒度与微细（粉）末收得率的影响。
The selection of pipe wall thickness, the calculation and design key points of the melt flow, melt pipe flow pressure fall and melt flow speed in the design of melt pipes were introduced in detail.
介绍了熔体管道设计中管道壁厚选择、熔体流量、熔体管道流动压力降和熔体流速等计算方法和设计要点。
The factors that affect thin-wall mould warpage, such as mould temperature, melt temperature, rate of injection and holding pressure, etc, are analyzed, in addition the ca…
对影响薄壳塑件翘曲变形的因素（如模具温度、熔体温度、注射速率、保压压力等）进行分析，提出翘曲产生的原因及相应的改进措施。
The factors that affect thin-wall mould warpage, such as mould temperature, melt temperature, rate of injection and holding pressure, etc, are analyzed, in addition the ca…
对影响薄壳塑件翘曲变形的因素（如模具温度、熔体温度、注射速率、保压压力等）进行分析，提出翘曲产生的原因及相应的改进措施。
应用推荐