When hope in a wide temperature range of use, transmission medium viscosity index should be higher.
当希望在某一较宽的温度范围内使用时，输送介质的粘度指数应该高些。
Because of the small spring easily plug solids, high viscosity medium will move in small delay compensation axial spring.
因为小弹簧容易被固体物堵塞，高粘度介质会使小弹簧轴向补偿移动受阻。
Due to high speed, high viscosity pump inside the rotor is barely formed when running idle, surrounding medium by sliding, cause not feeding, or flow rate is small.
由于转速过高，使高粘度泵在运转时内部转子几乎只是形成了空转，围绕所输送介质打滑，造成吸不上料，或者是流量很小。
The viscosity of the liquid medium reflects the ease of mobility, high viscosity, friction will increase, reducing output power, a waste of energy and have a high temperature.
液体的粘度反映了介质流动的难易程度，粘度过高会增加内摩擦阻力，降低输出功率，浪费能量，并产生过高的系统温度。
Also, viscous media can not be applied, and that specific product for the medium viscosity range is relatively narrow.
另外，粘稠状介质不能适用，而且，特定的产品适用的介质粘度范围相对较窄。
Particularly in the transport of high viscosity medium, you need to make more precise calculations.
尤其在输送高粘度介质时，需要作比较精确的计算。
When the viscosity of the liquid delivery higher, or when the system work in a cold environment, we must ensure that the transmission medium can flow smoothly.
当输送液体的粘度较高，或当系统在寒冷环境工作时，必须确保输送介质能够顺畅地流动。
So choose stainless steel high viscosity pump is must indicate the specific temperature, and medium lubricity.
所以选择不锈钢材质的高粘度泵是一定要注明具体的使用温度，及介质的润滑性。
When the viscosity of the medium being transferred is higher than 100cp, volumetric rotating piston pumps can be used.
当被输送介质的粘度大于100厘泊时，可选用容积式旋转活塞泵。
Therefore, high viscosity pulp has its own features in the filtering mechanism and the selection of filtering medium and filtering equipment.
因此高粘度浆体的过滤机理、过滤介质和过滤设备的选择方面也有自身的特点。
In this article, we research quartz crystal viscosity sensor and its frequency characteristic in liquid medium.
文中进行了液相介质中石英晶体粘度传感器及其频率特性的研究。
High flour whiteness, low ash content, medium protein content, medium to strong gluten strength and good extensibility, and high starch viscosity were desirable for Chinese noodle quality.
中国面条要求面粉颜色白、灰分低，较高的蛋白质含量、中等偏强的面筋强度和较好的延展性以及较高的峰值粘度。
The existence of the particle movement, increase block medium dispersion medium viscosity.
粒子的存在阻碍介质的运动，增加分散介质的黏度。
This means that pumps could be dry turn, self-absorption and processing of high viscosity, high abrasion medium.
这就意味着泵可以干转、自吸以及处理高黏度、高磨损介质。
Identity of viscosity for test solution and its blank solution, and the effect of medium and detection limit were studied.
对介质影响、试液与空白溶液粘度一致性及检出限进行了考察。
HCH-201 unsaturated polyester resin is designed for centrifugal casting molding glass pipe (HOBAS pipe) design of the structure layer resin is a low viscosity, medium reactivity of o-benzene resin.
201不饱和聚酯树脂是专门为离心浇铸成型玻璃钢管道(HOBAS管)设计的结构层树脂，是低粘度，中等反应性的邻苯型树脂。
Internet advertising medium has been recognized by more advertisers for its accuracy, interactivity and high user viscosity.
互联网广告媒介以其精准、互动性强、用户黏度高等特点得到了更多广告主的认可。
In the acid medium, the viscosity mechanism of the system of latex particles containing carboxyl is the same with that of the common hard sphere latex system.
在酸性介质中，含羧基乳胶粒子体系的致粘机理与普通硬球型乳胶粒子体系一致。
Unreinforced, nucleated, medium viscosity polybutylene terephthalate resin for fast injection molding.
无加强，核，介质粘度，聚对苯二甲酸丁二酯树脂的快速注塑成型。
Transport high viscosity medium, low speed pump to be elected, if the low viscosity, the corresponding high-speed selectable.
输送高粘度介质时，泵应选低转速，若粘度较低，相应可选择高转速。
If the high viscosity pump medium viscosity is too high, and with the rotation speed is too high, will cause the pump flow rate is very low, the noise of the pump is very large.
如果高粘度泵输送的介质粘度过高，而所配的转速也过高的话，就会造成泵的流量很低、泵的噪音很大。
Unreinforced, nucleated, medium viscosity, black polybutylene terephthalate resin for fast injection molding.
无加强，核，介质粘度，黑色的聚对苯二甲酸丁二酯树脂的快速注塑成型。
Determine the bag size depending on the filtration flow, viscosity of the medium, filtration precises.
根据过滤流量、介质粘度、过滤精度这三要素，确定滤袋的尺寸。
Unreinforced, medium viscosity, black polybutylene terephthalate resin for injection molding.
无加强，中等粘度，黑色的聚对苯二甲酸丁二酯树脂注塑成型。
An unreinforced, medium viscosity polybutylene terephthalate resin for extrusion and injection molding. It has been developed for consideration into applications such as parts for the food industry.
挤压的一个未加强，中等黏度聚丁烯对苯二酸盐树脂和注坯模型。它为考虑被开发了成应用例如食品工业的零件。
Product description: Flame retardance, medium viscosity, injection moulding grade.
产品描述：阻燃，中等粘度，注塑品级。
Medium viscosity, flame retardant PC.
中等粘度，阻燃的PC。
Medium viscosity PC Copolymer blend, enhanced UV stabilization, mold release added.
介质粘度PC共聚物混合、增强的紫外线稳定、脱模补充道。
SS 88is a high performance pale colour medium viscosity mineral cutting oil. SS 88is fortified with inactive sulphurised chlorinated compound, chlorine and fatty oil.
SS 88是高性能淡黄色中黏度矿物油切削油，含有大量不活性硫、氯复合添加剂、氯化物及脂肪油。
SS 88is a high performance pale colour medium viscosity mineral cutting oil. SS 88is fortified with inactive sulphurised chlorinated compound, chlorine and fatty oil.
SS 88是高性能淡黄色中黏度矿物油切削油，含有大量不活性硫、氯复合添加剂、氯化物及脂肪油。
应用推荐