They created a simple measuring process.
他们想出了一种简单的衡量方法。
The overall measuring process is controlled by an IBN-PC computer.
全部测量过程都由计算机控制，操作方便。
The measuring process of the impact weighers is analyzed by experiments.
对冲板流量计的测量过程进行试验分析。
This paper introduces a kind of photoelectric hybridization measuring process.
本文介绍了一种光电混合测定方法。
Note, the stick part should be clean; touching is forbidden in measuring process.
注意，粘接部位要干净，测温过程中禁止用手触摸。
The new measuring process which is based on null measurement is simple and reliable.
测试中采用一种新的消光法，使测量过程简单可靠。
Gear measuring process is an important part of metalworking practice for high education institutes.
高等院校工程训练中齿轮测量工艺是金工实习过程中一个重要组成部分。
The results show that the detector, annealing, measuring process can influence the monitoring result.
结果表明：探测器、退火程序、测量测序的变化都会影响测量结果。
Some practical problems arising from the measuring process of the silver-films of vacuum flasks are discussed.
探讨了若干实际测量保温瓶瓶胆银层厚度时出现的问题。
One of the core issues in landform's reverse measuring process is seeking the matching dot-pairs of landform images.
求解地貌图像匹配点对是地貌反求测量过程中的核心问题之一。
Since the quantity of the satellite is very limited, the precision of the result is low in dynamical measuring process.
由于“北斗”定位卫星数量极其有限，接收机在动态定位的精度上会出现很大的误差。
The volume measuring process includes the measurement of the level inside the container and sensor measurement of weight.
测量容积的方法包括测量容器内液面高度和传感器测重量。
In dynamic measuring process, the same standard rod gets different measuring outcome in different place within measuring range.
动态测量时，同一个标准件在测量范围内的不同位置测量结果不同。
The quick and accurate disposal of the inductosyn output signal is demanded during the displacement measuring process in machining.
在机械加工过程的位移检测中要求对传感器输出的信号进行快速、准确的处理。
An absolute range measuring system that can separate the target locating process from the measuring process is proposed in the paper.
提出一种将目标定位过程和测量过程分开的绝对距离测量系统。
This paper introduced mode of collecting, technology of filtering and measuring process about image of three dimension composite preform surface.
首先介绍了三维编织复合材料预制件表面图象的采集方式、滤波技术以及平均编织角的测试过程；
The precision of the measurer is high, the linearity measurer is commonly used in the daily production, and the measuring process is quite simple.
该测量仪的精度较高，并且能在日常生产中经常使用，测量的方法也相当简单；
Products the whole measuring process is controlled by computer, the results measured directly with digital display viscosity value, not conversion.
产品整个测量过程用电脑控制，其测量结果直接用数字显示粘度值，不用换算。
Errors are inevitable in all the stationary and dynamic measuring process which prevents us to get the real value of the measured quantity directly.
在一切静态测量与动态测量中不可避免的会产生测量误差，测量误差的存在使我们不能直接得到被测量的真实值。
The measuring process and its method is of practical use for monitoring the operational steadiness of sets as well as for their acceptance procedures.
其测试过程和方法对机组的稳定性监测和机组的验收具有实用性。
Presently in standing tree's diameter measuring process, the main tools are tape meter or caliper, which need manpower to read and record measure data.
目前，国内外在单株立木直径测量过程中，主要使用的还是需人工读取和记录测量数据的测径围尺或轮尺等树木测量工具。
In the measuring process, the output water content of the oil does not only depend on water content, the environmental temperature also has certain influence.
在油品检测过程中传感器的输出值不只取决含水量一个参量，环境温度对测量值也有一定的影响。
The measuring process was controlled automatically by applying the microcomputer and the IEEE-488 bus. The desired data were computed directly after the measurement.
整个测量过程由微型计算机自动进行控制，并在测量结束后直接计算出所需要的数据。
Aiming at the beam occlusion of a single emitter and single receptor laser sensor, an automated approach for avoiding occlusion during measuring process was presented.
针对普通单光源单接收器传感器普遍存在的反射光线遮蔽现象，提出了一种自动消除光线遮蔽的方法和测点快速重定位算法。
At last, it offers measuring process and results analysis of force effectiveness of an example of extended air defense missile C3I system with above measuring methods.
最后给出了一个扩展防空导弹体系C3I系统作战效能的评估过程和结果分析。
The system has the functions of automatic control, automatic measurement, automatic record of data and characteristic curve, form output, alarming in measuring process.
该系统具有测试过程自动控制、自动测量、数据及特性曲线自动记录、报表输出、报警功能。
It is shown that the errors in the measuring process are filtered to a large extent, and the reliability of the calculated friction forces is increased by using this method.
结果表明，所提出的方法在相当大程度上滤去了测量过程中的误差，减少了人为因素的影响，增加了摩阻力计算的可靠性。
In reverse engineering, in order to acquire surface data of sample part, multiple scanning of measuring process is usually required to adapt to the configuration of the part.
逆向工程中为了获取被测物体不同方位的表面信息，通常采用多次测量的方法。
In reverse engineering, in order to acquire surface data of sample part, multiple scanning of measuring process is usually required to adapt to the configuration of the part.
逆向工程中为了获取被测物体不同方位的表面信息，通常采用多次测量的方法。
应用推荐