It can enhance the measuring accuracy by correcting offset from heave, roll, and pitch of vessel.
姿态传感器能够改正或消除船载仪器由于船体的垂荡、横摇和纵摇引起的测量误差，大大提高测量精度。
This modification has important significance for improving the measuring accuracy of the model JSG-1 laser velocity interferometer.
这对提高JSG—1型激光速度干涉仪的测试精度具有重要意义。
This is an effective approach to improving the sensitivity and measuring accuracy under the same condition for the Michelson interferometer.
这是使迈克尔逊干涉仪在同样条件下提高灵敏度及测量精度的一条途径。
A tubing length intelligent measurer was developed in the light of low measuring accuracy, high labor intensity and low efficiency of manual measuring.
针对油管长度人工计量方法存在的计量精度差、工人劳动强度大、生产效率低等问题，研制了以单片微机为核心的油管长度智能计量仪。
The results of the experiment indicate that these circuit designs raise the measuring accuracy of the phase laser distance measuring system effectively.
综合实验结果表明，这些电路设计对于提高相位式激光测距仪的测量精度是有效的。
The factors to affect the measuring accuracy are analyzed.
最后分析了影响测试精度的因素。
The measuring accuracy of the on-axis component is also discussed in this paper.
本文中还给出了该仪器的系统设计参数并分析了轴向分量的测量精度。
Software calibration method is used to increase measuring accuracy and reliability.
采用软件校正，提高了测量精度和整机的可靠性。
With the new differential pressure method, the measuring accuracy is as high as 2%.
用新式压差法测量蒸发器水位，其测量精度高达2%。
The focus of this paper is how to enhance the measuring accuracy of CNC gear measuring machine.
本文是以如何提高大型数控齿轮测量中心测量精度为目的而展开研究的。
Thus, the measuring accuracy of this method is a little lower than that of the multi-step method.
因此，反向法与多步法相比，测量精确度略低。
These results are from improving instrument quality and increasing instrument measuring accuracy.
并报告了改进仪器质量和提高仪器测量精度的一些实验结果。
Improving measuring accuracy of rate biased laser gyro Angle rate is important to its application field.
提高速率偏频激光陀螺静态角速率测量精度在其应用领域具有重要的作用。
This method increases the measuring accuracy and efficiency greatly about the aerostatic bearing rigidity.
该方法大大地提高了气体静压轴承刚度的测试精度与测试效率。
The processing circuits in the vortex flowmeter are unable to ensure the measuring accuracy in the industrial fields.
涡街流量计中的处理电路不能保证仪表在工业现场的测量精度。
RESULTS The measuring accuracy of low loss and high loss dielectric materials was high, and measuring errors were low.
结果对低损耗和高损耗介质的测量精度都较高，测量误差较小。
A reversal method for error compensation of this system is provided so as to improve the measuring accuracy effectively.
文中提出了利用反转法对系统的误差进行补偿的原理和方法，有效地提高了系统的检测精度。
Sets forth all kinds of factors that affect the time parameter measuring accuracy, and proposes fairly reasonable methods.
阐述了影响时间参数测量精度的各种因素，并提出了较合理的方法。
The results show that the system has high measuring accuracy, high applicability at the site and relatively higher practical value.
结果表明，该系统测量精度高，现场适应性强，具有较高的使用价值。
The influence of various parameters on the measuring accuracy of the convective heat-transfer coefficient was analyzed quantitatively.
本文全面分析了各因素对对流换热系数精度的影响，并进行了定量分析。
Since the ultimate measuring accuracy is limited by the accuracy of calibration, a new method of calibration is proposed in this paper.
由于测量的精度最终要受到标定精度的限制，本文引入了一种新的标定方法。
The system has high measuring accuracy, fast machining speed and better automaticity, becoming the quality assurance of work machining.
这些系统测量精度高、速度快、自动化性能强，成为工件加工的质量保证。
The instrument introduced in the magnetostrictive technology has high measuring accuracy, low cost, long life and easy installation etc.
该仪表采用磁致伸缩技术，具有测量精度高、成本低、寿命长和安装简便等特点。
This paper analyse the influences of precision of bridge, measuring jig and so on to measuring accuracy, and discusses the improvements.
本文分析了电桥的精度、测量夹具等因素对测量结果准确性的影响，并提出了具体改进措施。
Combninig the technique of optical interferometry and TV image processing has the advantage of high measuring accuracy and real time response.
光学干涉计量与电视图象处理技术结合具有测量精度高和实时性好的优点。
The circuit and method for obtaining equal measuring accuracy and response speed in a wider frequency signal range are discussed in this paper.
本文探求在较大的被测频率信号范围内获得相同的测量精度与响应速度的测量方法及电路。
It is illustrated how to reasonably select measurement reference for complex parts in order to improve measuring accuracy and lower measuring error.
阐述了一些复杂零件如何合理选择测量基准，以提高零件的测量精度，减小检测误差。
With the aid of the microcomputer technique, extremely high angular resolution and measuring accuracy can be achieved by using a simple construction.
采用本方法与现代微机技术相结合，可以用非常简单的结构实现对小角度的高精度测量。
Many automotive performance tests are conducted on chassis dynamometer, while tyre rolling resistance is an important factor to affect measuring accuracy.
许多汽车性能试验均在底盘测功机上进行，而轮胎滚动阻力是影响测试精度的重要原因。
Many automotive performance tests are conducted on chassis dynamometer, while tyre rolling resistance is an important factor to affect measuring accuracy.
许多汽车性能试验均在底盘测功机上进行，而轮胎滚动阻力是影响测试精度的重要原因。
应用推荐