User may specify the DC bias, measurement amplitude, and pulse width of the measurement signal.
用户可以设定测量信号的直流偏压，测量振幅，脉冲宽度。
Several methods for oversampling of current measurement signal are introduced, for example, algorism filter, etc.
介绍电流测定信号的过采样的几种方法，例如十进制滤波器等。
Its measurement signal is to lead into harmonic signal digital measurement analysis system via ta end screen voltage signal amplifier.
其测量信号是经过TA末屏电压信号放大器引入谐波信号数字测量分析系统的。
For every process there must be final actuator that regulates the supply of energy or material to the process and changes the measurement signal.
对每一过程，均必须由最终的控制器来调节过程中能量或材料的供给量，并且改变测量值。
To the balance-structure, on the one hand, the right sense organ is important to the system performance, for it directly getting the measurement signal.
内旋式纸浆浓度变送器的性能除了体现在平衡机构上，而且还体现在系统控制算法的选择上。
When the fault appears, there will be some variation in the fractal dimension of measurement signal, and the fault detection can be carried out according to this change.
由于故障发生时系统表现异常，这些异常可导致测量信号分形维数的变化，根据这些变化可进行故障检测。
When a pneumatic transmission system is employed, the measurement signal is converted into pneumatic signal by the transmitter scaled from 0 to 100 percent of the measured value.
当使用启动传送系统时，测量信号就由变送器将比例为0% ~ 100%的测量值转换成气动信号。
According to amplitude analysis of the measurement signal, the probability DE sign method of finding the spring stiffness of the tractor's hydraulic draft control system is stud ied.
以实测信号为依据，通过幅值域分析，探讨了拖拉机液压系统力调节弹簧刚度的概率设计方法。
This method is based on digital signal analysis and time series modeling analysis, and can be applied to detection of measurement signal in engineering, analysis instrument or system.
这种基于数字信号分析和时序建模分析的方法，非常适应于工程测试信号检测、分析仪器和系统的诊断。
The phase detecting error caused by local oscillator frequency drift and non-synchronization of measurement signal and gate signal is eliminated and the measurement speed is improved at the same time.
该方法可以有效的消除因本振信号频率漂移及闸门信号与被测信号的非同步引起的测相误差，同时提高了测量速度。
For instance, when a neutrino strikes the detector in Gran Sasso, that signal has to travel 8km through a waveguide before a timing measurement can be made.
例如，当一个中微子击中格朗萨索的检测器后，该信号必须通过波导管传送8公里方能进行时间测量。
In a linear measurement, each photon would interact separately with the atoms, resulting in a relatively weak signal.
在一个线性测量中，每一个光子可以单独地与原子进行相互作用，这样得到的是一个相对较弱的信号。
Now they do say in the paper "It is worth stressing that this measurement does not rely on the difference between a start (t0) and a stop signal but on the comparison of two event time distributions."
他们的确在论文中提到“值得注意的是这一测量并不依赖于开始(t0)与结束信号之间的时间差，而是取决于两个事件的时间分布。”
In either case, the effects on the measurement can be considerable if enough of the unwanted signal is present.
在这些情况下，如果出现足够强的不希望有的信号，对测量的影响是相当大的。
Figure 10.22. Measurement configurations for each signal type.
图10.22。每一信号类型的测量配置。
Recorder in the process of dynamic measurement accuracy by record test best size of the error signal.
记录仪动态准确度的测量最好通过记录试验过程中的误差信号大小来实现。
For AC voltage measurement, an RMS converter circuit or a precision rectifier circuit convert the AC signal into a DC voltage.
对于交流电压测量﹐利用有效值转换电路或精密整流器电路将交流信号转换成直流电压。
For capacitive sensing, driving signal with DC bias voltage and ac voltage is usually necessary for the measurement of capacitance.
对电容式加速度计，为测量其电容的变化，通常需要带直流偏置的交流电压信号来驱动。
The signal generator null sensitivity affects the accuracy and resolution of measurement because the gyro is an integrating device.
因为陀螺是一种积分装置，所以信号发生器的零位灵敏度影响测量精度和测量分辨度。
However, to discuss signal measurement methods, you should classify a given signal as one of five signal types.
然而，在讨论信号测量方法时，你应该将所给信号归入五大类信号中的一种型号类型。
When added to the signal, it's easy to calculate the impact of this contact potential on the measurement accuracy.
当被增加到信号上时，则很容易计算出该接触电势对测量准确度的影响。
In this system, bridge measurement wiring is composed of foil gauges and signal outputted by sensors is transmitted to the display instrument.
该系统实现了由应变计组成的电桥测量线路，以及传感器输出信号的处理，并实时传送至显示仪表。
In the process of guided system simulation, we completed these works of Recognizing precision of collection signal, to select displacement measurement devices, signal conversion.
在制导系统仿真过程，本文完成了信号采集精度的确认、选择位移测量装置、信号转换等工作。
However, adding a switching system to facilitate the connection between the signal source and the measuring instrument also adds measurement uncertainties.
然而，在信号源和测量仪器之间通过切换系统建立连接会也会增加测量不确定度。
It is used for temperature measurement instruments and system that is an analogue signal output.
用于需要有模拟信号输出的温度测量仪表和系统。
Now let's look yet a little deeper into this measurement and try some alternate signal processing parameters.
现在，我们更深入地探究一下这个测量结果，并且尝试一些可能的信号处理参数。
The sensitivity of a measurement is the smallest change of the measured signal that can be detected.
测量的灵敏度是可以探测出的被测信号的最小变化量。
Measurement of the signal is usually vibration and noise, temperature, pressure, current, voltage, etc to one or more of the signal.
测量的信号通常是振动、噪声、温度、压力、电流、电压等信号中的一种或几种。
Measurement of the signal is usually vibration and noise, temperature, pressure, current, voltage, etc to one or more of the signal.
测量的信号通常是振动、噪声、温度、压力、电流、电压等信号中的一种或几种。
应用推荐