The method and experience for analyzing MCU embedded system domain are pointed out in conclusion, through the researches of the concept, the method, the process and the product of domain analysis.
通过对领域分析的相关概念、方法、过程以及产品的研究，从而得出在MCU嵌入式系统领域进行领域分析的相关方法以及经验。
Embedded system is the hardware and software system, which has been embedded in the application of product and engineering, and is cored with MCU.
嵌入式系统是指嵌入到各种产品或工程应用中的，以微处理器或微控制器为核心的软硬件系统。
The kernel of embedded system is embedded MCU, which requires fast processing speed, big memory, high performance of I/O port, low power waste, and fast respond.
嵌入式系统的核心是嵌入式处理器，要求处理速度块，存储容量大，I/O口功能强，功率损耗低，及时响应快等。
In embedded system, memory is very valuable, especially for 8-bit MCU, commonly with a few hundred bytes, or a few K RAM.
在嵌入式系统中，存储器是非常宝贵的资源，尤其对于8位微处理器而言，通常只有几百个字节的RAM，或者几千字节的RAM。
This paper gives the concrete method of reading and writing AT24C01A card in an embedded system which constituted by EP7312 MCU.
本文给出了EP7312单片机组成的嵌入式系统中读写AT24C01A卡的具体方法。
The application of two kinds of embedded modem in MCU system is discussed in this article.
探讨了两款嵌入式调制解调器在单片机系统的应用；
This system, which facilitates the utility of PC cameras in embedded application, is composed of MCU, USB Host Controller, high-speed RAM and FLASH memory.
此系统主要由单片机，USB主机控制器，高速RAM, FLASH存储器等器件组成，使得数码摄像头在嵌入式领域应用成为现实。
Embedded system based on ARM is composed of MCU, memory, JTAG circuit and power supply.
基于ARM的嵌入式系统的核心部分包括处理器、存储器、JTAG电路和电源部分。
Adoption of MODEM as an embedded system for transmission of data MODEM, MODEM and MCU through serial connections, the real-time transmission of data.
方案采用一个嵌入式的MODEM作为系统传输数据的MODEM, MODEM和单片机通过串口连接，实现数据的实时传输。
The applications of embedded system are still stay in the separate phases. The MCU is the core and it cooperates with monitoring, servo and indicating equipments to realize some functions.
嵌入式系统处于单独应用的阶段，以MCU为核心，与一些监测、伺服、指示设备配合实现一定的功能。
With the function of the task that the embedded system works on growing, the traditional 8-bit MCU can't content the request of the application.
现在随着嵌入式系统的功能增强，传统的8 位单片机已经越来越不能适应日渐复杂的应用需求。
According to the trait of embedded MCU applied system, we present some rational and new design methods for well program structure.
根据嵌入式单片机应用系统的特点，提出了新的程序结构的设计方法。
SOPC design is one of hotspots in embedded system fields. Using a mature MCU soft core is a crosscut to enter this field.
可编程片上系统(SOPC)是近期嵌入式系统设计的热点之一，利用成熟的处理器软核是进入这一领域的捷径。
Absrtact: the applications of embedded system are still stay in the separate phases. The MCU is the core and it cooperates with monitoring, servo and indicating equipments to realize some functions.
摘要：嵌入式系统处于单独应用的阶段，以MCU为核心，与一些监测、伺服、指示设备配合实现一定的功能。
In this paper, it has been coceived using a MCU or embedded system chips to achieve their communication with the PC machine.
本文提出了仅用一片MCU（微处器-单片机）或嵌入式系统芯片来实现其与PC机通讯的方法。
Designed an embedded and remote network motor control system based on DSP and MCU.
基于DSP与高速单片机m CU设计了一种嵌入式远程网络化电机控制系统。
The proposal based on USB Host/Slave controller chip CH375A, realized a USB-Host embedded in CAN bus data acquisition system and stored acquisition data of each node in U flash disk under MCU control.
该方案基于USB主/从控制芯片CH375A，在单片机的控制下，实现了CAN总线数据采集系统中嵌入USB主机，从而完成把各节点采集的数据存入U盘，取代了现场数据采集系统必须有一台计算机的模式。
The system employs a Fast Ethernet Physical Layer Chip and EMAC embedded in MCU to support network transmission.
使用物理层网络控制芯片配合微控制器片内集成的EMAC以太网控制器，提供对网络传输的支持。
An embedded system using RTOS has higher reliability, higher stability and higher speed, so porting RTOS to MCU is a necessary work of development MCU.
在嵌入式系统中使用实时操作系统，可以提高系统的稳定性、可靠性和实时性，因此为单片机移植操作系统是单片机开发的必要工作。
The embedded Internet system based on the 51 MCU has the characteristics of low-cost, simplicity, and high-adaptability in the applications.
本控制器具有成本低、开发简单快速、灵活等特点。
The system structure, technique index and its system application of NDBX1 electric fire monitor and alarm system which based on the embedded MCU technology were introduced.
本文以医学影像专业影像设备发展趋势为例，介绍了在医学影像专业引入嵌入式系统作为专业基础课程的思想和方法。
The system structure, technique index and its system application of NDBX1 electric fire monitor and alarm system which based on the embedded MCU technology were introduced.
本文以医学影像专业影像设备发展趋势为例，介绍了在医学影像专业引入嵌入式系统作为专业基础课程的思想和方法。
应用推荐