The MATLAB simulation program is coded to estimate the parametrically excited stability of the composite beams.
然后,编制MATLAB数值模拟程序,研究两种复合梁的参激稳定性。
In the study of modern control theories, pole assignment and LQR are designed on inverted pendulum systems, and the MATLAB simulation is researched.
利用息现代控制理论,针对倒立摆系统研究了极点配置方法和线性二次型最优控制方法,并利用MATLAB进行了仿真研究。
Analyses the inadequacy of the PID controller in current application, give a fuzzy adaptive PID controller and simulate with MATLAB simulation software.
分析了目前应用的PID控制器的不足,提出了一种模糊自适应PID控制器,并利用MATLAB软件对其进行了仿真。
PID, pole assignment and linear-quadratic optimal control (LQR) are used to design inverted pendulum systems. And they are researched by MATLAB simulation.
针对倒立摆系统研究了PID、极点配置和线性二次型调节器,并利用MATLAB进行了仿真研究。
It was concluded that the fuzzy control used in the brush roll control system of ECL could get a satisfying effect and better robustness by MATLAB simulation.
经仿真研究可以认为刷辊控制系统中采用模糊控制能达到较满意的控制效果,而且具有较好的鲁棒性。
Finally, through MATLAB simulation demonstrates and verifies the control performance of the proposed self-tuning control in comparison with the traditionally designed PID control.
最后,运用MATLAB仿真软件对广义最小方差自校正控制算法进行仿真,并与传统控制规律(常规pid控制)的仿真结果进行比较分析。
Through the MATLAB simulation, it is proved that this control algorithm can realize tracking to the assigned speed and enable the fluid class load to have very good stable performance.
通过MATLAB仿真看出,使用该控制算法可以很好地实现跟踪给定速度,使流体类负载有很好的稳定性能。
Then we repeat modifying its LC parameters through MATLAB simulation, compared with the design demand and the filter's responding characteristic to obtain the best filtering capability.
然后利用MATLAB进行仿真调试,对比设计要求和滤波器响应特性,反复调整滤波器lc参数,以获得最好的滤波性能。
The MATLAB simulation results show that the scheme provides the control system the stronger robustness and better control quality, and improves its dynamic and static performance index.
仿真研究表明,这种方案使汽包水位控制系统具有较强的鲁棒性及良好的控制品质,提高了系统的动静态性能指标。
After the mathematics model of the control object of the counter-gravity casting process is analyzed, PID controller is designed, and the PID parameters are determined by MATLAB simulation.
在分析反重力铸造过程控制对象数学模型的基础上,设计了PID控制器,并采用临界稳定法结合MATLAB仿真确定了PID参数。
In this paper, simulation is made for the algorithm by using MATLAB. Simulation results and experimental data have proved the algorithm's feasibility and effect, and have certain application value.
本文采用MATLAB平台对所述算法行了仿真,仿真结果和试验数据证明了本文所提算法的可行性和有效性,具有一定的应用价值。
In this paper, simulation is made for the algorithm by using MATLAB. Simulation results and experimental data have proved the algorithm's feasibility and effect, and have certain application value.
本文采用MATLAB平台对所述算法行了仿真,仿真结果和试验数据证明了本文所提算法的可行性和有效性,具有一定的应用价值。
应用推荐