The function call sigsuspend resolves this problem by resetting the signal mask and putting the process to sleep in a single atomic operation.
函数调用sigsuspend通过重置信号掩码并使进程休眠一个单一的原子操作来解决这一问题。
Technical disputes over the process, however, mask a more fundamental worry: that in hunting those with four-decade-old blood on their hands, Sheikh Hasina is conveniently hounding her enemies.
然而，有关法庭程序的司法争议也暗示着一个更为重要的担忧，即在搜捕那些在四十年前双手沾满血腥的凶手的过程中，塞克哈•哈希娜正在悠闲自得地逐步肃清其政敌。
Sometimes, people to wear a mask, flawless, even their own thought in the process of wearing a mask themselves are in fact and mask the.
有时候，人们把面具佩戴得天衣无缝，连他们自己都以为在佩戴面具的过程中自己实际上就成了和面具一样的人了。
LIGA mask technology based on silicon process technique and double side alignment is presented. The processing technology is simple.
提出一种基于硅工艺和双面对准技术的LIGA掩模技术，工艺十分简单。
The process was not only mental: she also had to put on 12 kilograms, and a makeup artist turned her nearly flawless face into a mask of tragedy.
这个过程不只是精神上的：她还必须增加12公斤体重，一位化妆师将她几近无瑕的脸变成了一张悲剧的面孔。
We developed a non silicon surface micro machining process with two or three mask electroplating layers and using polyimide or photoresist as sacrificial layers.
我们研制的非硅表面微机械工艺采用两次或三次掩模电镀层，聚酰亚胺和光刻胶分别作为底层和第二、第三层的牺牲层。
Compared with the technology for binary optical mask, the technology has the following strong points: process simplification, short period of fabrication and easy operation.
与二元光学元件掩模的制作工艺相比，该技术具有工艺简单、制作周期短且易于操作的优点。
Now SU8 resist has been used to make the LIGA mask for the LIGA standard process and some devices researching work.
SU 8光刻胶已应用于LIGA技术的标准化掩模制造工艺和一些器件的研究工作。
The manufacture of liquid photosensitive solder mask for PCB by screen printing is briefly introduced. The process and its quality control are also discussed in detail.
对印制板采用丝网印刷液态感光成形阻焊剂的制作进行了简单介绍，并对该制作工艺和品质控制进行了较为详细的论述。
The whole process is the morphology processing based on the gray-level image and binary mask, and is simple and easy to implement.
整个过程基本是对灰度图像和二值模板的形态处理，简单易行。
In the production process, First of all, according to calculations, using professional software LEDIT to draw the two mask graphics and produced.
在制作阵列位相环元件的过程中，首先根据计算设计的数据，使用专业软件LEDIT绘制了两块掩模版的图形并制作完成。
PCBA conformal coating, dam process, Solder mask coating, DIP Component fixing.
PCBA表面三防涂覆、堤坝工艺、涂防焊胶、DIP元件加固等。
ONLINE schedulers map to processors that are online in the affinity mask and are available to process threads.
ONLINE 计划程序在关联掩码中映射到处于联机状态的处理器，并且可用于处理线程。
The paper analyses the gray-tone mask physical mechanism, coding and optimum process.
本文分析了它的物理机制、掩模类型、编码过程、约束条件和优化方法。
The preparation process and the performance test of the ammonia absorbent for gas mask was introduced in this paper.
本文介绍了可用于现有防毒面具的氨吸收剂的制备方法及其性能测试方法。
Single step mask fabrication process is developed for LIGA technology, which made mask-making process simplified.
在LIGA技术研究中提出了一次掩膜成型法，简化了工艺过程；
Advance a series of parameters to support mask making, process, package and test.
提出工程中要求的一系列参数支持制版、流片、封装和验证。
And, those structures are simple to fabricate without any additional mask and implantation process.
且这三种结构皆简单制作而不需额外的光罩数和额外的离子植入。
In this tutorial we will be stepping through the process of animating an audio voice-over using mask-driven lip sync animation in After Effects.
在本教程中，我们将通过生动活泼的过程中加强了音频语音使用后效果面具驱动嘴唇同步动画。
Thus, there is no influence on the mask, even if the device undergoes the heat treatment at a high temperature during the manufacturing process.
因此，即使在制造工艺期间该器件在高温下经受热处理，对掩模也没有影响。
The execution of the liquid photoimageable solder mask of the printed circuit board was briefly introduced. The process and its quality control were also illuminated.
本文对印制板液态感光成形阻焊剂的制作进行了简单介绍，对该制程的工艺过程和品质控制进行了较为详细的论述。
The print table is then lowered by a fraction of a millimetre and the process repeated, with a different mask if required.
随后打印台面向下移动几分之一毫米的距离，然后放置不同的掩膜后，再重复上述操作。
It is effective to clean photo-mask in less than 10 minutes under the dry process.
其可在小于10分钟内有效的清洁光罩在乾燥制程下。
This article mainly explains the process of LIGA technology, which includes X-ray mask lithography, Micro-electroforming and Micro-copy.
本文主要阐述了LIGA技术的工艺过程，包括X射线深层光刻、微电铸和微复制工艺。
Final process-put decorations on the mask, like mustache or glasses, etc.
最后装上胡须、镜片等装饰物。
The process of making carbon nanotube array includes the following steps: providing one substrate and forming one mask layer on the substrate;
本发明涉及一种碳纳米管阵列制作方法，其步骤包括：提供一基底，在该基底上形成一遮挡层；
The process of making carbon nanotube array includes the following steps: providing one substrate and forming one mask layer on the substrate;
本发明涉及一种碳纳米管阵列制作方法，其步骤包括：提供一基底，在该基底上形成一遮挡层；
应用推荐