Nick set one end of a long socket extension on the intake manifold and listened to the other end.
尼克拿过来一根螺栓套杆，把一头儿贴在进气歧管上，然后凑过去听了听另外一头儿。
The standard wiper was driven by intake from the engine manifold, which was connected by a series of hoses to the wiper motor.
标准雨刷是由发动机歧管内部驱动。
The fuel system only has several major parts such as fuel tank, fuel pump, fuel filter, carburetor, intake manifold, etc.
燃料系只有这样几个主要部件，如燃油箱、输油泵、燃油滤清器、化油器、进气歧管等。
If the engine backfires, the sudden pressure in the intake manifold forces the valve back.
如果发动机回火，进气歧管骤增的压力就迫使阀门向后移动。
This paper introduces the calibration system and static and dynamic calibration method of an engine intake manifold pressure sensor.
介绍了发动机进气歧管压力传感器的标定系统和传感器静、动态标定方法。
The fuel system consists of the fuel tank, fuel pump, fuel filter, carburetor, intake manifold, and fuel lines, or tubes, connecting the tank, pump, and carburetor.
燃料系统包括汽油箱、汽油泵、汽油滤清器、化油器、进气歧管以及连接油箱、油泵和化油器的油管。
With the redesigned valves, the engine is not sensitive to air pressure and will easily run just by blowing into the intake manifold.
由于重新设计的阀门，发动机不敏感，空气压力，将很容易运行只需吹的进气歧管。
Taking the nonlinear character of intake system into account, the relation between manifold pressure and intake system parameters is given based on the intake dynamic model.
针对汽油机进气系统的非线性特性，基于汽油机进气通路动态模型，给出了进气压力与系统参数之间的关系。
This device, called the manifold heat-control valve, is built into the exhaust and intake manifold.
这种装置称为“歧管热控制阀”，它拼装在排气与进气歧管中。
The piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum.
活塞主要因进气歧管真空度的变化而在活塞腔内上下移动。
The Throttle body provides surfaces for mounting between the Motorcycle's air intake duct and the engine intake manifold.
风门表面留有安装摩托车进气管和发动机进气歧管的位置。
In many engines, the thermostat is located in a well in the intake or exhaust manifold.
在很多发动机内，恒温控制器装在进气岐管或排气岐管的空腔中。
The intake system mainly includes the air filter, intake ducting, the carburetor, and the intake manifold. Some engines have supercharger in the in take system.
进气系统主要包括空气滤清器、进气道、化油器和进气歧管。一些发动机在进气系统中有增压器。
The intake manifold connects the carburetor to the intake ports of the engine.
进气歧管把发动机进气道口连接起来。
The injection molding is an important tache to exploit plastic air intake manifold.
注塑成型工艺是开发塑料进气歧管的重要环节。
Engine fittings series:Gear chamber, Cavaera cover, Sprocket rooms cover, Preheaterbase, Water pump Cover, Intake manifold, Pump box.
发动机配件类：齿轮室、气门室罩盖、链轮室罩盖、预热器座、水泵泵盖、进气歧管、泵箱；
Summarized some important experience on designing injection mould of plastic air intake manifold.
总结出了在设计塑料进气歧管注塑模具时要注意的几个问题。
Load change in the engine intake manifold pressure changes that is when the spool displacement greater, gas output in response to faster.
在发动机负荷变化即进气管压力变化时，阀芯的位移更大，燃气输出量的响应更快。
In the P0442 example above, the fuel level, intake air temperature and manifold absolute pressure sensors are used.
在上面所给出P 0442示例中，燃油箱液面位置，进气空气温度和歧管绝对压力传感器将被应用。
This thesis mainly carries on research of three dimensional surface reconstruction of variable intake manifold and air fluid simulation analysis.
本文主要进行可变式进气歧管的三维曲面重建和空气流动模拟分析的研究。
The second part carries on the air fluid simulation analysis of variable intake manifold with the STAR-CD fluid software.
第二部分用STAR - CD流体软件对可变式进气歧管进行空气流动数值模拟分析。
Compressed air is injected at the left end of the intake manifold tube.
压缩空气注入在左端进气歧管管。
The Throttle body assembly will mount to the manifold snout and intake manifold interface dimensions are defined on the Throttle body assembly outline drawing.
节气门体总成安装在歧管口，进气歧管接口尺寸如节气门体总成轮廓图所示。
The effects of intake chamber volume, diameter and length of inlet duct and inlet manifold on volumetric efficiency were analyzed.
分析了进气总管和进气支管的管长、管径以及进气腔容积对充气系数的影响规律。
The picture below shows the timing shaft, timing gear and the intake manifold.
下面的图片中显示的时间轴，齿轮和时间的进气歧管。
The air filter is usually located in the air stream to your throttle valve assembly and intake manifold.
空气滤清器通常位于空气流到你的节流阀总成和进气歧管。
In order to improve engine efficiency and torque as well as the engine performance, plastic intake manifold was developed for CA4GE engine.
为了提高发动机的效率和扭矩、改善发动机的性能，针对CA4GE发动机研究、设计、开发了发动机塑料进气歧管。
In order to improve engine efficiency and torque as well as the engine performance, plastic intake manifold was developed for CA4GE engine.
为了提高发动机的效率和扭矩、改善发动机的性能，针对CA4GE发动机研究、设计、开发了发动机塑料进气歧管。
应用推荐