Machining error is a very complex non-linear problem.
机械加工误差是非常复杂的非线性问题。
Hereditary phenomnon of machining error and theory of relativity are intreduced.
介绍了加工误差的遗传现象和相关性理论。
At the same time, the machining error caused by the gravity bending of the ball screw is...
同时简要分析了在加工精密工件时，由于自重原因引起丝杠弯曲导致的加工工件的误差。
This paper is the first part of the machining error analyses and check groups of gear- hobbing.
本文是“滚齿加工误差分析与检验组”一文的第一部分。
On-line modeling, forecasting and compensating way for machining error in boring are introduced.
文章介绍了镗削加工误差的在线建模和预报补偿控制方法。
A novel algorithm, for machining error controlling in multi-point contact machining, is proposed.
同时提出了一种新的多点切触加工的加工误差控制方法。
There is machining error in electrical discharge machining (EDM) due to the electrode's orbiting.
在电火花成形加工（E DM）中，电极的平动产生了加工误差。
Due to the assembly and high positioning accuracy, so the machining error requirement is very small.
由于装配和定位精度高，所以加工误差要求很小。
The machining error affecting the load distribution are errors of the tooth flank direction and the contact line.
影响负荷分布性的加工误差主要因素是齿向误差和接触线误差。
Too much deflection was induced by the radial force, which resulted in the excessive machining error to the gear.
在径向力作用下，顶尖前端部产生过大挠度，造成齿轮加工误差过大。
Besides, the influence of the machining error by the nc model and the clearance Angle of the sway back are analyzed.
此外，还分析数控模型以及回摆间隙角对加工误差的影响。
To realize machining error compensation, it is necessary to measure the rotation error of machine tool spindle correctly.
本文提出了一种机床主轴回转误差补偿信号的实时测量方法。
An important machining error requirement in design was discussed, which serves as the basis for design of the differential.
同时讨论了设计中一项重要的加工误差要求，为差速器设计提供了依据。
When machining good-side workpiece or measuring its machining error, the points of these workpiece surface must be measured.
在加工具有大型复杂曲面的工件或对这些工件进行加工误差的检测时，都需要对曲面上的点进行测量。
It is very important to improve the gear accuracy, and is effective to decrease machining error by the pop NC compensation technology.
这对于提高滚齿的加工精度、特别是利用目前较热门的数控补偿的方法减小加工误差有着重要的理论和实际意义。
It is shown that bending deformation and the machining error in conditions of reversed turning is much less than that in normal turning.
算例表明：逆向车削时轴的弯曲变形以及加工误差远小于同等条件下正向车削的变形和误差。
The machining error affecting meshing stability comes from the cycling error of the machine's transmission chain and the error of the tools.
影响传动平稳的加工误差主要因素是来自机床传动链周期误差及刀具误差；
The relationship between the dividing error of the divider and the machining error of the serrated tooth discs has been found by experiments.
对于分度台的工作分度误差与齿盘加工误差之间的关系进行了实验验证。
However, in actual machining process, machining error caused by the cutter deflection influences the machining accuracy and the surface quality of the blade.
然而，在实际加工过程中，容易产生由刀具变形引起的加工误差，影响了叶片的加工精度及表面质量。
The paper analyzes machining error and its effect on the tooth profile accuracy according to the principal error, and gives the methods to diminish the error.
本文从方牙丝杠磨削的原理误差入手，分析了方牙丝杠加工的原理性误差及其对工件牙形精度的影响程度，提出了减小加工方牙丝杠原理误差的措施。
The method is efficient and precise, and lays a mathematic foundation for NC verification and machining error control in 5-axis sculptured surface manufacturing.
所用的计算方法高效精确，为复杂曲面加工过程的动态模拟和加工误差的控制奠定了数学基础。
Another one is to connect the injection pump to the driving gear with flange to avoid the influence from machining error of shaft and coaxial degree while installing.
二是将喷油泵与驱动齿轮间的连接方式改用法兰来连接，避免了由于轴的加工误差和安装同轴度的影响。
Since the parts' stiffness and precision of the spindle units are quit high, and the loads are usually not heavy, so the machining error caused by the cutting force is small.
在高速切削机床中，由于主轴单元系统各零件刚度和精度都较高，而负荷却不是很大，主轴因切削力引起的加工误差较小。
This article introduced the methods of data acquisition and processing by computer for machining error, and settled the problem of real time graph output in the manufacture process.
介绍应用计算机进行加工误差的数据采集与处理的方法，同时解决了企业生产过程中进行误差跟踪的实时图形绘制问题。
According to the feature of flexible machining, it be studied that the scheme and key technology of on-line modeling and prediction of machining error based on genetic neural network.
针对柔性加工过程的特征，研究了基于遗传神经网络的加工误差在线建模预报的方案和关键技术。
The text analyses some key problems of accurately machining of O circle mould cavity, including its technology, measurement, and machining error, and then puts forward a CAD example for it.
对O形圈模具型腔精确加工中的工艺、测量及加工偏差等几个关键问题进行了分析，并针对实例进行了计算机辅助设计。
Consequently, the prediction of the machining error in blade milling process and the investigation of active compensation can improve machining quality and processing efficiency significantly.
因而，针对叶片在切削过程中的误差进行预测及主动补偿技术的研究，对提高叶片加工质量和加工效率具有重要意义。
Consequently, the prediction of the machining error in blade milling process and the investigation of active compensation can improve machining quality and processing efficiency significantly.
因而，针对叶片在切削过程中的误差进行预测及主动补偿技术的研究，对提高叶片加工质量和加工效率具有重要意义。
应用推荐