This is done with the LSPV command (see Listing 7).
可以使用lspv命令来完成这项任务(见清单7)。
After you run exportvg, LSPV displays the volume group as none.
运行exportvg之后，lspv会将卷组显示为none。
Examine them with the LSPV and lsdev -dev hdiskX -attr commands.
用lspv和lsdev—devhdiskx—attr命令检查这些磁盘。
The LSPV command displays the same value as MAX REQUEST, as shown in Listing 1 below.
lspv命令将这个相同的值显示为MAXREQUEST，如下面的清单1所示。
You can also run the LSPV command on the hard disk and look at the value for MAX REQUEST.
还可以在硬盘上运行lspv并查看MAXREQUEST的值。
Both the LSPV and lsdev commands can display information relating to hdisks on an AIX system.
lspv和lsdev命令均可显示与AIX系统上的hdisks相关的信息。
Enter the LSPV command to list all physical volumes available on a computer, as shown in Listing 1.
输入命令lspv列出一个计算机上所有可用的物理卷，如清单1所示。
You can check the volume group status by listing physical volumes with LSPV. This shows the volume group name.
可以通过使用lspv命令列出物理卷来检查卷组状态：这里显示了卷组名。
Perform an LSPV command on each of the AIX nodes, and ensure that the nodes have access to all available storage.
在每一个AIX节点上都执行lspv命令，并确保这些节点可以访问所有可用的存储。
To verify that there is no longer any data on the DS8300 hdisks, the LSPV command is run and should not return any output.
为了验证ds8300hdisk上不再有任何数据，运行lspv命令，之后不应返回任何输出。
Using the LSPV command, check that both VIOS have the same PVID associated with the SAN storage (hdisk1, 2, and 3), as shown in Figure 3.
使用lspv命令检查两个VIOS中与SAN存储相关联的PVID是否相同(hdisk1、2和3)，见图3。
Run the LSPV command to display each hdisk's PVID that can uniquely identify the disk from any computer within the cluster, as shown in Listing 4.
在集群的每一台计算机上运行命令lspv显示每一个唯一标识磁盘的hdiskPVID，如清单4所示。
To confirm that all the data (logical volumes) for each of the old hdisks had been migrated, I ran the LSPV command to list the contents of each disk.
为了确认每个旧hdisk的所有数据(本地卷)都已迁移完毕，运行lspv命令来列出每个磁盘的内容。
Another method to check to see if you are mirroring is to use: LSPV -l and compare the output to make sure you have entries for each LV on both disks.
另一种检查方法是使用lspv- l，通过对比输出确认两个磁盘上都有每个LV的条目。
And when I found that I couldn't remove the one remaining logical volume, I went to other basic commands like LSPV, LSVG, and migratepv to gain information.
当我发现有一个逻辑卷无法删除时，就使用lspv、lsvg和migratepv等其他基本命令收集信息。
And when I found that I couldn't remove the one remaining logical volume, I went to other basic commands like LSPV, LSVG, and migratepv to gain information.
当我发现有一个逻辑卷无法删除时，就使用lspv、lsvg和migratepv等其他基本命令收集信息。
应用推荐