• But a growth in fees and surcharges is causing the low-cost airlines' fares to swell.

    不过,随着手续费附加费上涨,廉价航空票价不得不水涨船高。

    youdao

  • For those with sea legs, SeaStorm also includes a deeper analysis of wave heights, high wind, wind/wave forecasts, and swell direction (good for low-lying areas).

    如果你sealegs(Android机子上的附加装置),海洋风暴包括海浪高度疾风/预测海浪涌动方向特别是低洼地方)深入分析

    youdao

  • The low blood hefts also to cause by following factor: Although the liver disease, the nephrosis, swell slide, many medicine functions, the long time strenuous exercise, to drink have sprinkled.

    下列因素引起肝病肾病许多药物作用时间剧烈运动洒过虽

    youdao

  • Abnormal CT imaging of pancreas include swell, tumor, illegibility of peripancreas fat and low density areas in contrast pancreas and so on.

    胰腺异常CT征象为胰腺体积增大肿块、胰周脂肪层次不清增强后胰腺内密度

    youdao

  • The extrudate swell behaviour and the factors affecting it during short die extrusion of linear low density polyethylene (LLDPE) melt have been investigated by using a rheometer.

    应用毛细管流变仪,考察线性密度聚乙烯(LLDPE)熔体口型挤出中的胀大现象及其影响因素

    youdao

  • In circumstances where a low water level or total loss of water returns results in excessive vibration and torque, AUS-PLUG can be allowed to swell in water or mud for 15-20 minutes.

    水位或者返回损失导致过度震动扭矩情况下允许将AUS - PLUG膨胀水中泥浆中15 - 20分钟

    youdao

  • I folded my shawl double, and spread it over me for a coverlet; a low, mossy swell was my pillow.

    把披肩一折为二,身上作盖被,一个长满青苔的低矮小墩当了枕头

    youdao

  • The red clay and secondary red clay widely distributed in Liuzhou City have low-middle swell shrinking property as well as more higher strength.

    柳州市广泛分布粘土次生红粘土层强度普遍较高,但具有弱-中等的

    youdao

  • The swell factor tends to decrease if the cross section of die crown is large, the die round R is small, the runner is large, the dumping temperature is high and the extrusion speed is low;

    口型的冠部截面、口型圆角R、流胶口大,排胶温度挤出速度,则膨胀因数小;

    youdao

  • The swell factor tends to decrease if the cross section of die crown is large, the die round R is small, the runner is large, the dumping temperature is high and the extrusion speed is low;

    口型的冠部截面、口型圆角R、流胶口大,排胶温度挤出速度,则膨胀因数小;

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定