COAXIAL shaft, Two shafts rotating one inside the other for rotating the low and high pressure compressors by the low and high pressure engine turbines.
同心轴，两个套在一起旋转的轴。用于使发动机低压和高压涡轮分别带动低压和高压压气机。
If oil pressure was low and pump is within specifications, inspect for worn engine bearings or other reasons for oil pressure loss.
如果油压低并且泵在规格表内，则针对油压低的问题检查磨损的引擎轴或其它原因。
The rest of the heat may be allowed to escape, or, for maximum engine efficiency, the steam may be condensed in a separate apparatus, a condenser, at comparatively low temperature and pressure.
剩余的热可以排放，或者蒸汽可在单独的冷凝器中于较低的温度和压力下冷凝，以便获得最大的蒸汽机效率。
Stop engine, find causes and remove faults when oil pressure is low, water temperature is high, abnormal smokes or noise happen.
当出现机油压力过低、水温过高以及有异常排烟或响声时，应立即停机查清原因并进行排除。
The Stirling engine is effectively used with a gas bearing which has low pressure resistance to side force.
斯特林发动机和对侧向力抗压性低的气体轴承一起有效的使用。
An engine oil pressure alarming sensor of electron type automobile for detecting the oil pressure of automobile diesel engine and alarming if the engine oil pressure is too low.
一种电子式汽车机油压力报警传感器，用来检测汽车柴油发动机的机油压力，并具有在机油压力过低时报警的功能。
1 large exhaust — reduced exhaust back pressure, low torque will decline, engine exhaust will due to ultra high temperature burning simple.
改大排气——降低了排气回压，低扭会下降，发动机排气门将会由于超高温度简单焚毁。
Fuel-pump pressure and capacity can be checked with special gauges. Low pump pressure will cause fuel starvation and poor engine performance.
燃油泵的压力和流通能力可以用专门的仪器进行检查。泵油压力下降可引起供油不足，并降低发动机的性能。
Taking DF4B locomotive as an example, this paper analyses the reason of too low lubricating oil pressure in running diesel engine, and gives countermeasures for it.
以DF 4 B型机车为例，系统地分析了造成柴油机机油压力低的原因，并提出其判断方法和对策。
Applying this system to diesel engine need only to make some small modification on low-pressure oil way.
在柴油机上应用该系统只需对其低压油路部分加以改装即可，非常简单方面。
The performance of turbocharged diesel engines at different high altitudes was studied on the engine test bed for simulating high altitude (low air pressure).
在内燃机高海拔(低气压)模拟试验台上，对不同模拟海拔高度下的涡轮增压柴油机性能进行了试验研究。
The cleaning strainer base of 280 diesel engine in low pressure casting was discussed.
对280大功率柴油机铝合金滤清器座的低压铸造工艺进行了探讨。
The influence of low environment pressure on the main bearing and big end bearing of internal combustion engine was investigated based on a one-cylinder diesel engine.
以立式单缸柴油发动机为研究对象，分析了低气压对发动机主轴承和连杆大端轴承工作情况的影响。
The variable geometry turbocharger(VGT) is used to improve the performance of high pressure-ratio diesel engine, particularly at low load.
采用可变几何涡轮增压器（VGT）是改善增压柴油机低工况的有效方法。
But the fuel starting injection pressure will turn low gradually when the operational time of the diesel engine increases. This will cause worsening of the combustion process and fuel economy.
但是随着柴油机使用期的增长，启喷压力会逐渐降低，导致燃烧过程恶化，经济性下降。
Due to its inherent characteristics in reducing low frequency, small pressure loss and simple geometry, the resonant silencer is being extensively used in engine induction noise reduction.
由于共振式消声器具有结构简单、良好的消除低频噪声的性能和流动损失小等优点，因此在发动机进气噪声的控制中得到了广泛的应用。
The cyclic variation of the combustion pressure in the cylinder of a four-valve gasoline engine was analyzed at low speed and light load with the CB-466 combustion analyzer on the engine test-bed.
在发动机试验台上，用CB-466燃烧分析仪对四气门汽油机低速低负荷燃烧压力循环变动进行了试验研究。
The switch provides a low-pressure differential signal to the engine control system.
此开关为引擎控制系统提供一个低压差动信号。
Besides being coaxially connected with the low-pressure gas compressor, the air turbine can also be connected with a generator or a crankshaft of the internal combustion engine.
空气涡轮除了与低压压气机同轴相连外，还可以与发电机或内燃机的曲轴相连。
Considering the structure characteristic of turbo-charge blade wheel of complex aluminum alloy in vehicle engine, the production process for electromagnetic pump low-pressure coasting is determined.
结合车用发动机增压器叶轮复杂铝铸件结构特点，确定了电磁泵充型低压铸造生产工艺。
Considering the structure characteristic of turbo-charge blade wheel of complex aluminum alloy in vehicle engine, the production process for electromagnetic pump low-pressure coasting is determined.
结合车用发动机增压器叶轮复杂铝铸件结构特点，确定了电磁泵充型低压铸造生产工艺。
应用推荐