Increments a count in each loop iteration.
在每次循环迭代中增加一个计数。
Then, we assign $new to $current so it will be the "old" bit on the next loop iteration.
然后，我们将 $new赋给 $current ，以使之成为下一个循环中的 “old”比特。
For tasks that execute code in a loop, it is common to check for interruption only once per loop iteration.
对于执行一个循环中的代码的任务，通常只需为每一个循环迭代检查一次中断。
The best ways to improve loop performance are to decrease the amount of work done per iteration and decrease the number of loop iterations.
改善循环性能的最好办法是减少每次迭代中的运算量，并减少循环迭代次数。
For small loop bodies (that is, loop iterations with little computation), the prefetch scheduling distance must be more than one iteration.
对于小的循环体(即有很少的循环迭代计算)，预取距离必须调度不止一次迭代。
First of all, notice that you are potentially doing a lot of unnecessary work when the buffer runs out, since you are processing two buffers for each loop iteration.
首先注意，当缓冲区用尽时，可能要做许多不必要的工作，因为对于每个循环迭代都要处理两个缓冲区。
Add your configured and value-bound component to the current column, and end your column loop iteration by adding the completed column to the children of the DataTable.
将已配置和值绑定的组件添加到当前列中，通过将完成的列添加到DataTable的子项中结束列循环迭代。
If this program is run on a uniprocessor or unloaded multiprocessor system, each thread prints out close to the same for loop iteration count. In one run, the program printed.
如果此程序在单处理器或卸载的多处理器上运行，则每个线程打印的for循环迭代计数大致相同。
If so, skip to the next iteration of the loop.
如果是的话则跳过到循环的下个迭代。
For each iteration, all of the steps in the loop are run.
对于每个迭代，将运行循环中的所有步骤。
Most of this data is being deleted with the next iteration of the loop.
这些数据中的大多数会在循环的下一次迭代中删除。
This will only happen on the first iteration of the loop, saving valuable execution time on each subsequent iteration.
这样，它只在循环第一个迭代时执行，从而在以后每次迭代时节省了宝贵的时间。
There is data stored in the BPEDB for each iteration of a loop in a long-running business process.
对于长时间运行的业务过程中循环的每次迭代，都要在BPEDB 中存储数据。
Condition, "this thing in the middle between the semicolons, is going to be checked every iteration of the loop."
条件，“这个在两个分号的中间，它将迭代地检查这个循环的条件。”
When it discovers a loop, it displays three expressions: the initializer, condition, and iteration.
当它发现一个循环时，会显示三种表达式：初始程序、条件及迭代。
Rather than checking the loop condition before each iteration, the condition is checked at the end of the iteration.
与在每次迭代前检查循环条件不同，而是在迭代结束时检查条件。
When a for statement is executed, a cursor is implicitly declared such that for each iteration of the for loop, the next row is the result set if fetched.
在执行for语句时，游标被隐式声明，这样对于FOR循环的每一次迭代，取回的下一行就是结果集。
While loops have a loop condition that is evaluated before each iteration.
While循环具有在每次迭代之前评估的循环条件。
When an activity is skipped in an end state, the request targets the next iteration of this activity, for example, if it is located inside a while loop or inside a cyclic flow.
当跳过某个处于结束状态的活动时，请求将指向此活动的下一个迭代，例如，如果该活动位于while循环中或者在循环流中。
As discussed in the previous article, the continue statement causes the containing loop to start the next iteration.
如前面的文章中所述，continue语句使包含它的循环开始下一次迭代。
This means that a Repeat Until Loop will always have at least one iteration.
这意味着RepeatUntil循环始终会至少有一次迭代。
For-each loop: When iterating over an array, the compiler generates an induction variable and the standard array iteration idiom.
for - each循环：当迭代数组时，编译器生成归纳变量和标准的数组迭代语法。
You will recall that DataTables execute an implicit loop over their rows, and the var attribute indicates the value of the current row during the iteration.
您将再次调用 DataTables 对各表行执行隐式循环，var属性指示迭代过程中的当前行。
Since the loop condition is checked before each iteration, the steps in the loop would not run at all if the condition is initially false.
由于在每次迭代之前检查循环条件，因此，如果条件最初为false，则循环中的步骤不运行。
Note at the end of the loop that I recursively call the same function with an argument that is one greater than the previous, implementing the iteration of the loop.
注意，在循环的结尾处，我用一个比上次大1的参数递归地调用同一个函数，以实现循环的迭代。
There's more: the for loop can be utilized to iterate over any object that supports the iteration metaphor, which makes the for loop very powerful.
还有更多信息：for循环可以用于迭代支持迭代metaphor的任何对象，这使for循环非常有用。
Each user starts on a random iteration count (first, fifth, and so on), and each user runs for the entire 64 iterations. The loop followed this pattern.
每个用户从一个随机的迭代计数(第1，第5，等等)开始，每个用户都运行整整64次迭代。
Because filenum will always be less than filecount, the integer division filenum/filecount will always produce zero, so each iteration of the loop will echo
由于filenum始终小于filecount，整数除法 filenum/filecount将始终生成0，因此每次迭代循环都将生成
zero() is slowest, because the JIT can't yet optimize away the cost of getting the array length once for every iteration through the loop.
zero()是当中最慢的，因为对于这个遍历中的历次迭代，JIT并不能优化获取数组长度的开销。
zero() is slowest, because the JIT can't yet optimize away the cost of getting the array length once for every iteration through the loop.
zero()是当中最慢的，因为对于这个遍历中的历次迭代，JIT并不能优化获取数组长度的开销。
应用推荐