Calculation of the joint under load slip -off conditions shows that there are great possibilities in tensile failure of the bolts. Measures for increasing the bolt strength are discussed.
通过对失载工况下该螺栓联接的计算表明，螺栓被拉断的危险性很大，并讨论了提高该螺栓联接中螺栓强度的主要措施。
Linear bearings provide low stick slip for precise positioning and ease of moving the load.
直线轴承提供低坚持滑精确定位和方便移动的负载。
The paper analyzes the limited load of wedge by unified strength theory, finds its solution in slip line and discusses its application in geotechnical engineering.
采用统一强度理论对楔体进行了极限分析，得到了极限荷载的滑移线解，并讨论了其在岩土工程中的应用。
An axisymmetrical finite element analysis is also made, with which the secondary cracking load and the end slip after secondary cracking can be predicted.
又作了轴对称的有限元分析，能估算次生裂缝出现时的荷载以及次生裂缝出现后的端部滑移。
When the load is removed, the elastic portion of the strain is recovered, but the plastic part (slip and creep) remains as permanent set.
当荷载被移走时，应变的弹性部分恢复，但塑性应变部分(滑移和徐变)却会永久呆留。
After a mathematic analysis of the slip ratio of Continuously Variable Transmission (CVT), the effect of CVT load is discussed.
本文首先介绍了无级变速器滑差率的数学分析，讨论了无级变速器负载对滑差率的影响。
The persistent slip bands were determined by the observations of the substructure near the surface of gear steels on fatigue load.
通过对在疲劳载荷作用下渗碳齿轮钢次表层亚结构的观察发现有持续滑移带形成。
However, the difference is that the continuous composite slab can carry further substantial load even after the shear slip initiation as against the simply supported slab.
但与简支组合板不同的是，连续组合板端部出现滑移后，其极限承载能力明显高于相同跨度简支板极限承载力。
The control system can realize working sites data automatic gathering and control of exhaust gas, noise, headlight, side slip, axle load, brake, etc.
汽车检测线智能化控制系统能实现尾气、噪声、灯光、侧滑、轴荷、制动等工位数据的自动采集控制。
This thesis focuses on bond failure modes, failure mechanics, factors influencing bond behavior, bond shear stress-slip relationship and bond failure load.
研究内容包括：粘结破坏模式、破坏机理、粘结性能影响因素、粘结剪应力—滑移关系及极限粘结承载力等。
It is analyzed under time-varying side slip angle and constant wheel load.
在不变载荷下以时变侧偏角为激励，对轮胎模型进行了计算。
This paper puts forward a new method for solving hysteresis loop and stick-slip Phenomenon in large torque, high load and low speed conditions, i. e. PWMtype NC proportional directional control.
本文针对大惯量、大负荷、低速工况的滞环及爬行现象，提出了一种新型的解决方法——脉宽调制（PWM）型数控比例方向阀控制。
At the same rotating speed and eccentricity ratio, the slip effect reduce the gas pressure curvature and hence the load carrying capacity.
在相同的转速和偏心率下，滑移流效应降低了气压分布的曲率，进而降低了气浮轴承所能够提供的承载能力。
The liquid resistance value can be altered by adding in standby raw material and is applicable for slip ring electrical motor of light load, medium load and heavy load starting up.
液体阻值通过添加备用原料来改变。适用于轻载，中载，重载起动的滑环电机。
The liquid resistance value can be altered by adding in standby raw material and is applicable for slip ring electrical motor of light load, medium load and heavy load starting up.
液体阻值通过添加备用原料来改变。适用于轻载，中载，重载起动的滑环电机。
应用推荐