The flow of liquid steel in the mold was displayed.
模拟显示了结晶器内的钢液流动；
The liquid steel physic simulation usually is water simulation.
钢液物理模拟的主要方法是水力学模拟。
ANSOB process is one of more advanced in treatment of liquid steel.
OB是目前钢水处理过程中较先进的工艺之一。
It turns the body to liquid steel. It makes it vibrate like a guitar.
它让身体变成钢液，让身体像吉他一样的震动。
The paper describe the basic production process of cleaning liquid steel.
本文论述了洁净钢生产的基本过程。
This paper presents an example of fuzzy control of the liquid steel level.
本文以钢水液位控制系统为例提出了一种模糊控制方案。
Liquid steel refining through slag modification has been investigated in the paper.
研究了炉渣精炼对于钢水洁净度的影响。
The vibration of converter is studied which is caused by the movement of liquid steel when oxygen blown.
研究了吹炼时炉液运动引起的转炉振动情况；
On the basis of the study, the stirring energy of bottom-blown CO_2 in liquid steel hasanalysed theoretically.
并在此基础上对底吹CO_2的钢液搅拌能力进行了理论分析。
The dynamics of purifying the liquid steel by centrifugal flow tundish was studied through physical simulation.
采用物理模拟的方法，对离心中间包净化钢液的动力学进行了考察。
By discussing about sampling method of liquid steel in converter, this article puts forward new sampling methods.
通过对转炉冶炼钢的熔炼成分取样方法的探讨，提出新的取样方法。
To lower the superheat of liquid steel, a water-cooled nozzle is designed to be used into commercial run in the paper.
为了降低钢液的过热度，设计了一种水冷水口，使它能够应用在实际生产中。
Base on the analysis of heat balance of LF-VD-CC process, the liquid steel temperature control model has been developed.
在分析LF - VD -CC过程各阶段热平衡状况的基础上，开发了LF - VD - CC过程中钢液温度控制模型。
The refining technologies of liquid steel before it is poured into tube bloom on continuous casting machine are introduced.
介绍了连铸机浇铸管坯之前钢水的处理技术。
This paper studied liquid steel flow property in mould of super low head slab CC with hydraulic model and mathematics model.
本文应用水力学及数学模型的方法研究了超低头板坯连铸结晶器内钢水流动特征。
The effect of all kinds of technique on controlling Nitrogen and Oxygen content in liquid steel to lower level is explained.
论述了各种不同工艺技术对控制钢中较低氮、氧含量水平的作用。
Powder injecting device is a key equipment which enables powdered flux to be injected into liquid steel continuously and stably.
如何使粉剂连续稳定的进入钢水中，喷煤罐是关键设备。
Analyzing the heat transfer of thermometric sensor for liquid steel, a relevant finite element model is developed for the sensor.
在分析钢水测温传感器传热过程的基础上，建立了测温传感器的有限元模型。
The paper presents the relationship between liquid steel fluidity and deoxidation requirements, deoxidation measures theoretically.
本文从理论上阐述连铸钢水流动性同钢水脱氧要求、脱氧方式之间的关系。
The improvement of slab equiaxed crystal ratio by electric pulse on liquid steel in continuous casting mould of Panzhihua steel No.
从结晶器施加电脉冲的输入能量、电脉冲频率、钢液过热度角度，探讨电脉冲技术提高铸坯等轴晶率的效果。
Argon bubbles distribute unevenly and the gas holdup of liquid steel in the upper region is far higher than that of the lower region.
氩气的分布不均匀，上回流区钢液的含气率大大高于下回流区。
The improvement of slab equiaxed crystal ratio by electric pulse on liquid steel in continuous casting mould at Pan steel slab castor No.
从结晶器施加电脉冲输入能量、钢液过热度、电极间距三方面，探讨电脉冲处理提高铸坯等轴晶率的效果。
The experimental study on control of nitrogen in liquid steel during EAF melting, LF refining and continuous casting have been carried out.
通过生产试验研究了电弧炉冶炼过程、L F精炼过程及连铸过程钢液氮的控制。
Under the condition of the liquid steel that is deeply oxidized, the oxides in the molten slag can better denitrogenate from the molten steel.
钢液在深脱氧的情况下，熔渣中氧化物能较好脱出钢液中的氮；
The effect of the initial state on the solidification process of liquid steel and the temperature changing inside furnace were discussed, respectively.
讨论了正常熔化时间即断电前炉内状态对断电后钢液凝固和炉内温度变化的影响。
On the basis of the study the deoxidation alloying process and Ladle refining process are put forward in order to check nitrogen pick-up in liquid steel.
在此研究基础上，提出了脱氧合金化及钢包精炼工艺，以减少钢液吸氮。
The present paper studies the effect of structure of the submerged nozzle on the flow ability of the liquid steel in the mold of the slab continuous caster.
通过水力模型实验，研究了水口结构对南钢板坯连铸机结晶器内钢水流动特性的影响。
The pound region volume of the baffle C type is still too small, so the liquid steel can't mix sufficiently, and the average residence time in the tundish is short.
型挡墙，冲击区体积较小，钢液混合不均匀，钢液在整个中间包内的平均停留时间较短。
The practice indicates that the quality of liquid steel is improved, the inclusion and gas content is decreased. The steel properties conform the national standards.
生产实践证明，底吹氩能改善和提高钢水的内在质量，降低钢中夹杂物含量和气体含量，吹氩后钢质的力学性能符合国家标准。
The multiple versions of EMS in the continuous casting of flat products are reviewed and classified with respect to liquid steel flow pattern and metallurgical results.
回顾了电磁搅拌应用于扁平产品连铸生产中的各种形式，并按液态钢水流动形态和冶金效果给予分类。
应用推荐