In this paper the formula of requisite linear damping for overcoming shimmy is derived according to the point contact theory of wheel shimmy.
本文根据机轮摆振的点接触理论,导出了为克服摆振所需线性阻尼的计算公式。
The transverse method, in which both the grinding wheel and the workpiece rotate and longitudinal linear feed is applied to enable grinding of the whole length.
横向方法:这种方法中砂轮与工件均旋转且采用线性纵向进给以保证能磨削整个长度。
The grinding system which uses linear motor as a wheel feed drive is introduced.
介绍了利用直线电机作为砂轮进给驱动的磨削系统。
Structure design of smooth wheel roller with variable linear load, which is new and special, is introduced, the changing characteristics and practical use of the roller are discussed.
介绍了一种独特新颖的可变线载荷刚性光轮压路机压轮碾压面的结构设计,探讨了此结构压轮的线载荷变化特性及实用性。
Better machining result has been obtained by using vitrified bond CBN grinding wheel on the microshift feeding device of elastic tool carriage driven by the linear motor.
在直线电机驱动弹性刀架的微位移进给装置上,采用陶瓷结合剂C BN 砂轮进行磨削加工试验研究,得到了较好的加工效果。
This paper introduces the transient state response of the vehicle model which has two linear degrees of freedom with a step input of the front wheel.
介绍了在前轮角阶跃输入下线性二自由度汽车模型的瞬态响应,讨论了行驶车速对汽车瞬态响应的影响。
Two post is more linear in the travel. Also give more outside wheel lock for the same inside wheel lock.
两个后更在旅游线。也让更多的外部为同一内部车轮锁车轮锁。
Analysis has been carried out on the mechanics in a kind of new typed linear transmission of differential wheel based on synchronous cog belt.
对一种新型的基于同步齿形带的差动轮线性传动中的力学进行了分析。
The influence of depth of grinding, feed rate and circular linear speed of the grinding wheel on the grinding forces with respect to the maximum chip thickness of a single active diamond was analyzed.
从单颗金刚石最大切削厚度的角度,分析了磨削深度、进给速度和砂轮线速度对磨削力的影响。
The principle of a measurement system used to inspect the wheel tread contour of locomotives and cars with linear CCD image sensor is introduced.
讨论了一种应用线阵CCD图像传感器测量火车车轮踏面磨损量的检测系统; 分析了系统的测量原理;
Workbench drives workpiece for linear running to and for; polishing machine provides power to drive polishing wheel to turn and polishing wheel as the polishing media.
工作台带动工件往返做直线运动,电机输出动力带动抛光轮旋转接触工件进行抛光,抛光轮上加固体或液体两种抛光蜡作为抛光介质。
The original drive part used in well-known drive system of man driven vehicle becomes basically linear reciprocating structural member and wheel-type unit is used.
它是在公知的人力车传动系统中,原动件改为可作基本线性的往复运动的构件,并采用轮式装置。
Optimal Damping Ratio(OPR) of a suspension system was existed and proved by linear vibration model on suspension system of multi-wheel vehicle.
在多轮车辆悬挂系统线性振动模型基础上,证明了悬挂最优阻尼比的存在。
When the wheel diameter becomes smaller, can improve the wheels' rotate speed, but can not exceed the wheels' linear speed.
砂轮直径磨小时,可以提高转速,但不能超过砂轮规定的线速度。
The wheel maximum linear velocity should be accord with the machine tooling specification requirement.
砂轮最高工作线速度要符合机床规格要求。
The wheel maximum linear velocity should be accord with the machine tooling specification requirement.
砂轮最高工作线速度要符合机床规格要求。
应用推荐