NOTE: On pump discharge, the preferred check valves are in-line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵出口处，首选止回阀是管内弹簧负载，配置杠杆和重量旋启式结构，或杠杆和弹簧旋启式结构。
Note: On pump discharge, the preferred check valves are an in-line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵排泄口，首选的止回阀是管内弹簧负载，带杠杆和压铁或杠杆和弹簧的旋启式止回阀。
NOTE: On pump discharge, the preferred check valves are an in-line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵的排泄口处，首选的止回阀是管内弹簧负载，旋启式，配置杠杆和重量或杠杆和弹簧。
For surface crack in pipe, this paper presents the finite element model including line spring element that is used for J integration calculation, as well as numerical examples.
对管道上的表面裂纹采用线弹簧单元，建立了裂纹管道J积分计算的有限元模型，给出了J积分的计算实例。
The in-line spring-actuated lift check also is referred to as the "silent check" because the spring closes the valve before gravity and fluid reversal can slam the valve closed.
由于这种止回阀能够在重力和介质倒流撞击启闭件之前关闭阀门，因此这种直通弹簧驱动升降式止回阀也称为“静音”止回阀。
On pump discharge, the preferred check valves are in-line spring loaded, swing design with lever and weight or lever and spring.
在泵出口处，首选止回阀是管内弹簧负载，配置杠杆和重量旋启式结构，或杠杆和弹簧旋启式结构。
Note: on pump discharge, the preferred check valves are an in - line spring loaded, swing design with lever and weight or lever and spring.
注意：在泵的排泄口处，首选的止回阀是管内弹簧负载，旋启式，配置杠杆和重量或杠杆和弹簧。
Add the 10-line Spring configuration file for the DAO.
为dao添加10行spring配置文件。
The stress intensity factors of multitudinous arbitrarily distributed coplanar surface cracks are solved by using the line - spring model.
采用线弹簧模型求解多个共面任意分布表面裂纹的应力强度因子。
Non-linear dynamics characters of a rotor system for an elastic shaft-disk with a crack are examined by introducing the geometric non-linearity and equivalent line-spring model.
本文引入了几何非线性关系和等效线弹簧模型对含裂纹的弹性轴弹性盘转子系统进行非线性动力学分析。
The ALC? is an in-line, spring assisted, single guided "wafer" check valve designed to prevent "water hammer" and "reverse" flow.
同轴、管内螺纹弹簧单导对夹式止回阀，专门用于防止水击作用和倒流现象。
In this paper, the equivalent line-spring model is employed to study the dynamic stability of a rotating cracked shaft.
本文用等效线弹簧模型计算裂纹转轴的动力稳定性问题。
In this paper, the equivalent line-spring model is employed to study the dynamic stability of a rotating cracked shaft.
本文用等效线弹簧模型计算裂纹转轴的动力稳定性问题。
应用推荐